Quadra-Fire QF130 User Manual

Page 9

Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11

Figure 2.3 Control Module

NG/LP SETTING

STATUS INDICATOR LED

SELECTOR

SWITCH

FLAME HI/LO SWITCH

I. Before Lighting Fireplace

Before operating this ﬁ replace for the ﬁ rst time,

have a

qualiﬁ ed technician:
• Verify all shipping materials have been removed from

inside and/or underneath the ﬁ rebox.

• Review proper placement of logs, ember material and/

or other decorative materials.

• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position

and that the integral barrier is in place.

WARNING! Risk of Fire/Asphyxiation! DO NOT oper-

ate ﬁ replace with ﬁ xed glass assembly removed.
• An Intelliﬁ re Plus

™

ignition system is standard with this

appliance.

H. Control Module Operation

1. The control module has an ON/OFF/REMOTE selector

switch that must be set. See Figure 2.3.

OFF Position: Appliance will ignore all power inputs and

will not respond to any commands from a wall switch or

remote. The unit should be in the OFF position during

installation, service, battery installation, fuel conversion,

and in the event that the control goes into LOCK-OUT

mode as a result of an error code.

ON Position: Appliance will ignite and run continuously

in the HI ﬂ ame setting, with no adjustment in ﬂ ame

output. This mode of operation is primarily used for

initial installation or power outage operation with battery

backup.

REMOTE Position: Appliance will initiate commands

from an optional wired wall switch and/or the wireless

remote (RC300).

2. If using a wired wall switch with the module in REMOTE

mode, the ﬂ ame output can be adjusted with the HI/LO

selector switch on the module. See Figure 2.3. Note

that the ﬂ ame HI/LO selector switch will become inactive

once an optional remote control (RC200/RC300) is

programmed to the control module. Note that the control

module will always ignite the ﬁ replace on HI and remain

so for the initial 10 seconds of operation. If the HI/LO

is switched to the LO position, the ﬂ ame output will

automatically drop to the lowest setting after the ﬂ ame

has been established for 10 sec. After this 10 second

period, the ﬂ ame can be adjusted from HI to LO with

the switch.

3. The control module has safety feature that automatically

shuts down the ﬁ replace after 9 hours of continuous

operation without receiving a command from the RC300

remote.

4. If you intend to use both an optional wired wall switch

and the RC300 remote control to operate your ﬁ replace,

the wall switch will override any commands given by

the remote.

Module Reset
This module may lock-out under certain conditions.

When this occurs, the appliance will not ignite or

respond to commands. The module will go into lock-out

mode by emitting three audible beeps, then continuously

displaying a RED/GREEN error code at its status

indicator LED.

• Check battery tray. Remove batteries if installed.

Batteries should only be installed for use during power

outages. See Section G.

• Locate the module selector switch. (See Figure 2.3).
• Set the module selector switch to the OFF position.
• Wait ﬁ ve (5) minutes to allow possible accumulated gas

to clear.

• Set the module selector switch to ON or REMOTE

position.

• Start the appliance.
WARNING! Risk of Explosion! DO NOT press the mod-

ule reset switch more than one time within a ﬁ ve minute

time period. Gas may accumulate in ﬁ rebox. Call a quali-

ﬁ ed service technician.

