Omega Vehicle Security PTC900 - Manual (Page 28)

28
7-SrL Serial Communication Parameters
DISPLAY PARAMETER
FACTORY
SETTING
USER SETTING
bAUd BAUD RATE 9600
dAtA DATA BITS 7
PAr PARITY BIT Odd
Addr METER UNIT ADDRESS 00
Abbr ABBREVIATED PRINTING NO
REAL-TIME CLOCK PRINT FORMAT YES
OPt PRINT OPTIONS
t-dSP TIMER DISPLAY YES
C-dSP CYCLE COUNTER DISPLAY NO
rtC-d RTC DATE DISPLAY NO
rtC-t RTC TIME DISPLAY NO
spNt SETPOINT VALUES NO
SPNtOF SETPOINT OFF/ TIME-OUT VALUES NO
PARAMETER USER SETTING
FACTORY
SETTING
dSP-t 12-59p
dSP-d DATE DISPLAY FORMAT 12-31
SyNC
Ch-dSt
sLAVE
N0
OFFSEt
CAL
00
TIME DISPLAY FORMAT
DISPLAY
AUTO TIME CHANGE FOR D.S.T.
SYNCHRONIZATION UNIT TYPE
CALIBRATE REAL-TIME CLOCK
RTC CALIBRATION OFFSET VALUE
9-fCS Factory Service Parameters
DISPLAY
DISPLAY INTENSITY LEVEL 3 d-LEV
FACTORY
SETTING
USER SETTING PARAMETER
Shaded areas are model dependent. Shaded areas are model dependent.
8-rtC Real-Time Clock Parameters
OUt-n
tOUt-n
SPOF-n
OFF-n
SP-n
ON-n
ASM-n
ACt-n
DISPLAY
NOr NOr NOr NOr SETPOINT ANNUNCIATOR
POWER-UP STATE
NO NO NO NO OUTPUT RESET W/DISPLAY RESET
NO NO NO NO TIMER/COUNTER AUTO RESET
NOr NOr NOr NOr OUTPUT LOGIC
VALUE VALUE VALUE
000100
000100
000100
VALUE
000100
VALUE
VALUE
000100
000100
000100 SETPOINT OFF VALUE (B)*
VALUE
SETPOINT OFF (B)*
TIME-OUT VALUE (B)*
TIME-OUT VALUE (A)
000100 SETPOINT OFF VALUE (A)
VALUE SETPOINT OFF (A)
LAtCH LAtCH LAtCH
VALUE
NO
Mon-Fri
Mon-Fri
Mon-Fri
Mon-Fri
000000
000000
VALUE
VALUE
NONE
SP-4
USER SETTING
NO
Mon-Fri
Mon-Fri
Mon-Fri
Mon-Fri
000000
000000
VALUE
NONE
SP-3
LAtCH
FACTORY
SETTING
USER SETTING
FACTORY
SETTING
VALUE
NO
Mon-Fri
Mon-Fri
Mon-Fri
Mon-Fri
000000
000000
VALUE
VALUE SETPOINT ON (B)*
NONE
SP-2
SETPOINT ACTION
USER SETTING
NO TIMER STOP
Mon-Fri DAILY OFF OCCURRENCE (B)*
Mon-Fri DAILY OFF OCCURRENCE (A)
Mon-Fri DAILY ON OCCURRENCE (B)*
Mon-Fri DAILY ON OCCURRENCE (A)
000000 SETPOINT ON VALUE (B)*
000000 SETPOINT ON VALUE (A)
VALUE SETPOINT ON (A)
NONE SETPOINT ASSIGNMENT
SP-1 6-SPt Setpoint (Alarm) Parameters
FACTORY
SETTING
USER SETTING
FACTORY
SETTING
PARAMETER
PTC901 Application
A big application request has always been for
Real-Time Clocks to display time throughout the
plant. The challenge has been to keep all the
various clock locations synchronized with the
right time. With the new PTC901 Timer/Real-
Time Clock this problem is history. You can install
up to a maximum of 32 units. Simply select one of
the units in the system as the host and the balance
are programmed as slaves. The host will send out
a synchronization pulse every hour to correct the
time on any clock unit wired in the system.
Real-Time Clock Synchronization Network
* See Module 2, Exchanging Parameter Lists, for details on programming this value.