Onkyo TX-SR601E - Manual (Page 52)

52
Input Setup
STANDBY/ON
PHONES VIDEO 4 INPUT
DIGITAL
VIDEO 3 TAPE VIDEO 4
SURROUND THX DSP STEREO
STANDBY
DISPLAY
VIDEO 2 DVD VIDEO 1 AUDIO SELECTOR
LISTENING MODE
MASTER VOLUME RETURN
ENTER
AUDIO ADJUST SETUP
RT/PTY/TP
VCR 2 VCR 1 S VIDEO VIDEO AUDIO L R
OFF ON
POWER
TUNER CD PHONO DIRECT/ PURE AUDIO
PURE AUDIO
REC OUT ZONE 2 OFF LEVEL MEMORY
CLEAR
FM MODE
PRESET
TUNI NG
SETUP
RETURN
/ / /
RETURN SETUP
/ / /
ENTER
INPUT SELECTOR
buttons
Input source buttons
This menu allows you to make the various settings concerning the
signals input from the various input sources that you use with the
TX-SR701/701E/601/601E. The settings made in this menu are
valid for the input source that is currently selected with the input
source buttons at the front panel and, therefore, these settings are
made separately for each input source.
Setup Procedure
1. Select the desired input source.
2. Press the SETUP button on the front panel or SETUP
button on the remote controller.
The main menu appears.
3. Use the and cursor buttons to select “5. Input
Setup” and then press the ENTER button.
The “Input Setup” menu appears.
VIDEO 3 TAPE VIDEO 4 VIDEO 2 DVD VIDEO 1
VCR 2 VCR 1
TUNER CD PHONO
* Menu *****************
1.Hardware Config
2.Speaker Config
3.Speaker Distance
4.Level Calibration
5.Input Setup
6.Preference
|ENTER|Quit:|SETUP|
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
5.Input Setup
*** Input:DVD *******
a.Digital Input :OPT1
b.Component Video
:Input1
c.IntelliVolume
: 0dB
Quit:|SETUP|
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
5.Input Setup
*** Input:DVD *******
d.Analog/PCM/D.F.2ch
:Last Valid
e.PCM fs=96k
:Last Valid
f.D.F. :Last Valid
g.D.F.Mono:Last Valid
Quit:|SETUP|
4. Use the and cursor buttons to select an item and
then use the and cursor buttons to set the
desired value.
Press the RETURN button to return to the main menu.
Press the SETUP button on the front panel or SETUP button on the
remote controller to exit the Setup menu.
a. Digital Input
This setting tells the TX-SR701/701E/601/601E which input source
button on the front panel is connected with which digital input jack
on the rear panel.
For example, if the input source selected at the front panel is CD
and the compact disc player is connected to DIGITAL INPUT
OPTICAL 2, then select “OPT2” here. If the input source selected
is not connected to a digital input, then select “----.”
OPT1, 2: Select if the input source is connected to either of the
DIGITAL INPUT OPTICAL 1 or 2 jack.
COAX: Select if the input source is connected to the DIGITAL
INPUT COAXIAL jack.
– – – –: Select if the input source is not from a digital input jack.
The default settings are given below.
----: Available for digital input but not set in initial settings.
* TX-SR701/701E only
Notes:
• When you select “TUNER” for input, you cannot assign digital
input to “TUNER.”
• Since VIDEO 4 is fixed to the optical digital terminal on the
front panel, this item will be disabled if VIDEO 4 is selected.
Input source Digital input
CD COAX
PHONO* ----
TAPE ----
DVD OPT 1
VIDEO 1 ----
VIDEO 2 ----
VIDEO 3 OPT 2