Rover 9859 - 5HP Petrol - Manual (Page 6)

Rover Mowers Limited Chip `N Shred SAFETY INSTRUCTIONS
General Electrical Safety Rules
1. Avoid dangerous environments such as damp
locations.
2. Do not abuse the power cord. Never pull a machine
by the cord or pull the cord to disconnect it from the
outlet socket. Keep the cord away from excessive
heat, oil, and sharp edges.
3. Disconnect the machine when not in use, before
servicing and when changing attachments.
4. Avoid accidental starting. Be sure to switch off
before plugging the cord into a power outlet.
5. To prevent electrical shock, use the machine only
with an extension cord suitable for outdoor use as
recommended by the extension cord manufacturer;
the use of suitable extension cords is extremely
important for the operator's personal safety.
6. Never use an indoor type of extension cord: these
cords are designed for use with lamps and small
appliances and are inadequate for high-powered
machines.
7. Make sure the extension cord is in good condition. A
cord with cracked or broken insulation is hazardous,
particularly
in the presence of moisture or
combustible material. It is also important that the
cord connectors be of rugged construction, in good
condition, and securely attached to the outer jacket.
8. If the extension cord is damaged in any manner while
operating the machine, immediately switch off the
power supply and remove the extension cord from the
power outlet.
9. If the supply cord is damaged it must be replaced by
a CMG Service Agent or similarly qualified person in
order to avoid a hazard.
Electrical Supply Capacity and Fuses
1. Use only an electric circuit having adequate
capacity.
2. Blowing a fuse or tripping a circuit breaker is a
warning that you are overloading your machine or
have too many devices in use on that circuit, or
both. Determine the cause and correct it. Do not
install a higher capacity fuse.
1. SPECIFICATIONS
Rover Model No: 9885 (Electric) 9858 (Petrol) 9859 (Petrol)
Engine Model No: A09189 91202 135202
Power rating 2.42 Kw (High Torque) 2.6 Kw 3.75 Kw
Fuel Capacity 1.9 litres 2.85 litres
Oil Capacity 600ml 600ml
Oil Grade SAE 30 SAE 30
Spark Plug RJ 19 LM RJ 19 LM
Spark Plug Gap 0.7 - 0.8mm 0.7 - 0.8mm
Voltage 240 volts
Current FL. 10 amps
Frequency 50Hz
Phase Single
No. Flails 12 12 12
No. chipper blades 1 1 1
_
Chipper opening 71 x 71 mm 71 x 71 mm 71 x 71 mm
Weight 56 51 56
2. SETTING UP
2.1 Loose Parts Kit
Feed hopper half LH. ............................................ 1
Feed hopper half RH. ............................................. 1
Hopper baffle ........................................................ 1
Hopper handle ....................................................... 1
Hopper washers ..................................................... 4
Chipper tube assembly ........................................... 1
Manual .................................................................. 1
Bar screen assembly ............................................. 1
Screws- 10 x 3/4" pan p/head .............................. 12
Bolts- 1/4" x 1-1/2" unc. cuphead .......................... 4
Nyloc nuts- 1/4" unc. ............................................. 4
Screws- 3/16" x 5/8" mush.head.............................. 4
Nyloc nuts- 3/16" unc. ........................................... 4
Washer- 3/16" x 1/2" x 20g.flat ............................. 4
Washer- 3/16" x 3/4" x 16g.flat ............................. 4
Nyloc nuts- 5/16" unc. ........................................... 7
Setscrew- 5/16" x 1" unc. hex. ............................... 7
Washers- 5/16" x 5/8" x 18g. flat ........................... 7
When disassembling the timber packing, discard the four
nuts and retain the bolts and washers for the handle
assembly. The four nyloc nuts found in the loose parts
list are to be used on the handle bolts.