Rover 9859 - 5HP Petrol - Manual (Page 5)

Rover Mowers Limited Chip `N Shred SAFETY INSTRUCTIONS
Training
•
Become familiar with the Owner's Manual before
attempting to operate this equipment.
•
Do not allow children to operate this equipment.
•
Do not operate this equipment in the vicinity of
bystanders.
•
Carbon dioxide can be extremely dangerous in
enclosed areas; do not run the machine in an
enclosed area since the exhaust from the engine
contains carbon monoxide, which is colourless,
odourless, and tasteless.
•
Do not place hands or any other part of the body or
allow clothing inside the feeding chamber, discharge
chute, or near any moving part.
•
Before inspecting or servicing any part or the
machine, shut off the power supply, disconnect the
power cord or disconnect the spark plug lead from
the spark plug, and make sure that all moving parts
have come to a complete stop.
Preparation
•
Obtain and wear safety glasses and gloves at all
times while operating the machine.
•
Avoid wearing loose fitting clothing. Operate the
machine only on a level surface.
•
Do not operate the machine on a paved or gravel
surface. Thrown objects could cause injury.
•
Before starting the machine, check that all screws,
nuts, bolts, and other fasteners are properly
secured. Replace damaged or unreadable warning
and operator labels.
•
Use extra care in handling petrol and other fuels.
They are flammable and vapours are explosive.
a. Use only an approved container.
b. Never remove fuel cap or add fuel with the
engine running. Allow engine to cool before
refuelling. Do not smoke.
c. Never refuel the machine indoors.
d. Never store the machine or fuel container inside
where there is an open flame, such as a gas
water heater.
Operation
•
Before starting the machine, make certain that the
cutting chamber is empty.
•
When feeding shreddable material into the
equipment be extremely careful that pieces of metal,
rocks, bottles, cans or other foreign objects are not
included.
•
If the cutting mechanism strikes any foreign objects
or if the machine should make any unusual noise
or vibration, immediately switch off the engine and
allow the machine to stop. Disconnect the spark
plug wire from the spark plug or remove power
cord from power supply and take the following
steps.
a. Inspect for damage
b. Replace or repair any damaged parts.
c. Check for and tighten any loose parts.
Do not attempt to repair the machine unless you are
competent to do so.
•
Keep the engine clean of debris and other
accumulations to prevent damage to the engine or
possible fire.
•
Do not allow processed material to build up in the
discharge area. This may prevent proper discharge
and can result in kickback of material through the
feed opening.
•
Keep all guards and deflectors in place and in good
working condition.
•
Always stand clear of the discharge area when
operating this machine.
•
Keep your face and body away from the feed
opening.
•
Do not overreach. Keep proper balance and footing
at all times.
•
Do not tamper with the engine governor settings on
petrol engines; the governor controls the maximum
safe operating speed and protects the engine and all
moving parts from damage caused by over speed.
Seek authorised service if a problem exists.
•
Do not transport this machine while the engine is
running.
•
If the machine becomes clogged, switch-off the
engine and disconnect the spark plug lead or
remove the power lead from power supply, before
cleaning debris away.
•
Switch-off the unit before attaching or removing the
mulch bag.
Maintenance
•
When this equipment is stopped for servicing, in-
spection, or storage, or to change an accessory,
make sure the spark plug lead is disconnected from
the spark plug, or the power cord is removed from
power supply. Allow the machine to cool before
making any inspections, adjustments, etc. Maintain
the machine with care and keep it clean.
•
Store the machine out of the reach of children and
where petrol vapours will not reach an open flame or
spark. For extended storage periods, run the unit dry
of fuel. Always allow the machine to cool before
storing.