RCA 2-9120/2-9130 - Manual (Page 2)

S ERVICE
FCC requires this product to be serviced only by the manufacturer or its authorized service agents. In accordance with
FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the
user’s authority to operate this product. For instructions on how to obtain service, call 1-800-448-0329.
Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or
received as a gift. This information will be valuable if service should be required during the warranty period.
Purchase date ________________________________ Name of store _______________________________
2 3 4 5
FOLD FOLD FOLD
FOLD FOLD FOLD
I NSTALLATION
D ESKTOP OR TABLETOP INSTALLATION
1. Remove telephone line cord from the pocket on the
bottom of the phone.
2. Run telephone line cord through the guides on the
bottom of the phone.
3. Connect the telephone line cord to a modular
telephone jack.
4. Slide the RINGER switch (on the side of the handset)
to ON.
5. Set PULSE/TONE switch (on the side of the handset)
to TONE for touch-tone service, or set it to PULSE for
rotary service.If you don’t know which type of
service you have, check with the phone company.
W ALL M OUNT I NSTALLATION M ODULAR J ACK R EQUIREMENTS
You need an RJ11 type modular jack,
which is the most common type of phone
jack and might look like the one pictured
here. If you don’t have a modular jack,
call your local phone company to find out
how to get one installed. 1a. If the modular phone jack is
in the base plate on the wall
where you're going to mount
your phone, just plug the
telephone line cord into the
jack; mount the phone on
the posts; and set the
RINGER switch and PULSE/
TONE switch (described in
detail below).
ABC DEF JKL MNO TUV WXY OPER GHI PRS TONE 0000 0000 231 564 897 0#*
ON OFF RINGER TONE PULSE
U SING THE TELEPHONE FEATURES
1 2
3 4
ABC DEF
JKL MNO
TUV WXY
OPER
GHI
PRS
TONE
0000 0000
2 3 1
5 6 4
8 9 7
0 # *
ON OFF RINGER
TONE
PULSE
T ROUBLESHOOTING T IPS
Problem Solution
No dial tone. • Check hook switch to make sure it pops up.
Won't dial out • Make sure PULSE/TONE is set to correct position.
Phone doesn’t ring • Make sure RINGER switch is set to ON.
• You might have too many phones on one line.
Feedback when • This is normal. Power fluctuates with phone outpulsing.
dialing in PULSE mode.
Can’t be heard by • Make sure phone cord is securely plugged in.
other party • Make sure other phones aren't off the hook at the same time you're using the phone. It is
normal for the volume to drop when additional phones are used at the same time.
2. Plug telephone line cord into
the modular jack.
3. Slip mounting holes on the
bottom of the telephone over
the wall plate posts and slide
the base down until the
phone is firmly in place.
(Wall plate is not included.)
1b. If the modular phone jack is
near the floor and you want
to mount the phone on the
wall, remove the telephone
line cord from the pocket
that is on the bottom of the
phone. Wrap the phone
cord around the circular
guide on the bottom of the
phone.
2
3
4
5
1a
1b
4. Slide the RINGER switch (on
the side of handset) to ON.
5. Set PULSE/TONE switch (on
the side of the handset) to
TONE for touch-tone service,
or set it to PULSE for rotary
service.If you don’t know
which type of service you
have, check with the phone
company.
A UTOMATIC REDIAL
To automatically redial the last number you called:
1. Pick up the handset to get a dial tone.
2. Press REDIAL.
F LASH
Press the FLASH button instead of the hook switch to activate custom calling services
such as call waiting or call transfer. Custom calling services are provided by the phone
company.
T EMPORARY T ONE
If you have pulse service, you can temporarily change from pulse to tone service in order
to access services that require tone dialing (such as getting information from a local bank).
After dialing the telephone number, press and release the tone button, marked with an
asterisk (*). When you hang up, your phone telephone returns to pulse service.
FLASH
button
REDIAL
button
Telephone
line cord
Coiled
handset
cord
Mounting
holes
2
ABC
3
DEF
1
5
JKL
6
MNO
4
8
TUV
9
WXY
7
0 OPER # *
GHI
PRS
TONE
0000 0000 flash redial
2-9120 (Folded size 80 x 175 mm)
20724660
Sheet 2 0f 2 (Double-side printing with 3 Folds)