RCA Stereo Receiver with Remote Control - Manual (Page 10)

10
TUNING THE RADIO
Your receiver has four types of electronic tuning — manual,
automatic, direct, and memory.
Note: To listen to stations with weak signals, we recommend manual
tuning.
Manual and Automatic Tuning
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to that band and
displays the frequency last selected.
Note: If CH appears on the right side of the display, press
TUNING MODE to switch from preset to manual-tuning mode.
MANUAL briefly appears.
2. To manually select the next higher or lower frequency, press
TUNING UP or DOWN . Hold down UP or DOWN to rapidly
scan up or down through the frequencies. Release the button to
stop scanning.
To automatically search for the next higher or lower frequency with a
strong signal, briefly hold down
TUNING UP or DOWN . The
receiver searches up or down the band, stopping on the next
frequency with a strong signal.
Notes:
• TUNED appears when the received signal is strong.
• STEREO appears when the received FM broadcasts are in
stereo.
• If you press TUNING UP at the top of the frequency range or
TUNING DOWN at the bottom of the frequency range, the
frequency at the opposite end of the range appears.
Direct Tuning (Remote Control Only)
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to and displays the
frequency last selected in that band.
2. Press DIRECT TUNING on the remote control. DIRECT IN
scrolls by, followed by AM – – – – kHz for AM or FM – – – . – –
MHz for FM. The first – flashes.
3. Enter the desired frequency using the remote control’s number
buttons.
Notes:
• If you press 1 to enter a FM frequency, such as 103.5, 10
automatically appears. If you also press the zero, the
frequency that appears would be
100.30 .
• The last zero always appears automatically in both FM and
AM frequencies.
• If you do not press a key within 5 seconds, the receiver exits
direct tuning. Start over at Step 2.
Memory Tuning
Memory tuning lets you instantly tune to a stored frequency. You can
store up to 30 AM and 30 FM frequencies in the receiver’s memory.
The receiver automatically stores the first 30 stations found in the
selected band into the memory. You can also manually store a station
into memory.
A A A Au u u utttto o o om m m ma a a attttiiiicccca a a all ll ll lly S y S y S y Stttto o o orrrriiiin n n ng g g g S S S Stttta a a attttiiiio o o on n n nssss
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to that band and the
last selected frequency appears.
2. Hold down MEMORY for more than 2 seconds. MEMORY and
CH appear and the receiver scans through the frequencies,
beginning with the low end (87.5 MHz for FM or 530 kHz for
AM).
3. When the receiver finds a station, it stores it in the first memory
channel, the selected CH number appears, and the receiver looks
for the next station. When the receiver finds the thirtieth station
or when it reaches the high end of the frequency range,
MEMORY
disappears and the receiver tunes to the lowest frequency station
in the band.
Repeat these steps to automatically store stations in the other band.
M M M Ma a a anu nu nu nua a a all ll ll lly y y y S S S Stttto o o orrrriiiin n n ng g g g a S a S a S a Stttta a a attttiiiio o o on n n n
Follow these steps to manually store a station, or to replace a station
already stored in memory.
1. Press FM or AM on the front panel (or on the remote control) to
select the desired band. The receiver tunes to and displays the
frequency last selected in that band.
Note: If CH appears on the right side of the display, press
TUNING MODE to switch to manual-tuning mode. MANUAL
briefly appears.
2. Tune to the desired station (see “Manual and Automatic Tuning”
on Page 10).
3. Press MEMORY . MEMORY flashes on the display.
4. While MEMORY flashes, press TUNING UP or DOWN until the
desired memory channel number appears.
5. Press MEMORY again to store the station immediately. Or, wait
about 5 seconds and the station is automatically stored in the
selected channel.
Notes:
• If you store a frequency in a memory channel that already
contains a frequency, you replace the previous frequency.
• If your receiver is disconnected from AC power for several days,
it loses all the stored frequencies.