Radio Shack 43-1122 - Manual (Page 10)

10 Installation
Note: If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
not dial the access code either.
If the dial tone stops, you have touch-
tone service. If the dial tone continues,
you have pulse service.
3. Press TALK .
To set the dialing mode, hold down FLASH
until the phone beeps and the current dialing
mode appears. Press
# /
7 7 7 7
to set pulse mode
or
∗
/TONE/
6 6 6 6
to set tone mode.
Fkbi[ Fkbi[ Fkbi[ Fkbi[ :_Wb_d] :_Wb_d] :_Wb_d] :_Wb_d]
or
Jed[ Jed[ Jed[ Jed[ :_Wb_d] :_Wb_d] :_Wb_d] :_Wb_d]
appears.
Note: The phone exits the setting mode if a
call or page is received, or if you press
TALK .
SETTING THE RINGER TONE
AND VOLUME
You can select one of four different ringer
tone/volume settings on the handset. Lift the
handset and repeatedly press
8 8 8 8
or
9 9 9 9
to
select the desired ringer setting. Each time
you press the button, the phone rings at the
selected setting and the display shows
H_d]ý H_d]ý H_d]ý H_d]ý
Jof[э7э>_]^ Jof[э7э>_]^ Jof[э7э>_]^ Jof[э7э>_]^
,
H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem H_d]ýJof[ý7ýBem
,
H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^ H_d]ýJof[э8э>_]^
,
or
H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem H_d]ýJof[ý8ýBem
.
TURNING AUTO TALK ON/
OFF
Your phone is preset so you must press
TALK when you lift the handset from the base
to answer a call. With Auto Talk turned on,
you can answer a call by just lifting the
handset from the base. If the handset is
away from the base, you can answer by
pressing any key.
Follow these steps to turn Auto Talk on or
off.
1. Lift the handset and hold down CALL ID
until the menu appears with
7kje 7kje 7kje 7kje JWba JWba JWba JWba
selected.
2. Press SELECT to change the Auto Talk
setting.
Ed Ed Ed Ed
or
E\\ E\\ E\\ E\\
appears indicating the
selected setting.
3. Return the handset to the base (or press
CALL ID ) to store the new setting.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show
Caller ID information for an incoming call
even while you are using the phone.
Follow these steps to turn the Caller ID/Call
Waiting feature on or off.
1. Lift the handset and hold down CALL ID
until the menu appears with
7kje 7kje 7kje 7kje JWba JWba JWba JWba
selected.
2. Press 2 or
9 9 9 9
to move the cursor to
9?:9M0 9?:9M0 9?:9M0 9?:9M0
(Caller ID/Call Waiting).
3. Press SELECT to turn the Caller ID/Call
Waiting setting on or off.
Ed Ed Ed Ed
or
E\\ E\\ E\\ E\\
appears indicating the selected setting.
4. Return the handset to the base to store
the new setting.
STORING YOUR AREA
CODE
You can store your local area code in the
phone’s memory so it will not show the area
code if you receive a local call. If you need to
add or store the area code for a local
number, you can add it afterwards (see
“Adding/Deleting the Area Code” on
Page 16).
Important: In some areas, the area code is
necessary even for a local call. If you live in