Roland PNC-900 - Manual (Page 25)

19
Instruction Format Meaning of Parameter [Parameter Range (Default)] Explanation
!NR !NR [terminator] None Not Ready
!PG !PG n [terminator] n: [-1600 — +1600 mm] Page Feed
!ST !ST n [terminator] n: [0, 1] Select Tool
• Instructions in mode1 and mode2
Instruction Format Meaning of Parameter [Parameter Range (Default)] Explanation
OA OA; None Output Actual Point
OC OC; None Output Commanded Position
OE OE; None Output Error
OF OF; None Output Factor
When the PNC-900 receives an OF instruction from the computer,
"40,40 [TERM]" is output.
OH OH; None Output Hard-Clip Limits
OI OI; None Output Identification
When the PNC-900 receives an OI instruction from the computer,
"900 [TERM]" is output.
OO OO; None Output Option Parameter
When the PNC-900 receives an OO instruction from the computer,
"0,0,0,0,1,0,0,0 [TERM]" is output. The "1" in this output indicates that
circle and arc commands have been loaded
OP OP; None Output P1 & P2
OS OS; None Output Status
OW OW; None Output Window
PA PA x1, y1(...,xn, yn); xn, yn: Absolute XY coordinates [*1] Cut Absolute
PA;
PD PD x1, y1(...,xn, yn); xn, yn: XY coordinates [*1] Tool Down
PD;
PR PR ∆ 1, ∆ y1(... ∆ xn, ∆ yn); ∆ xn, ∆ yn: Relative XY coordinates [*1] Cut Relative
PR;
PT PT d; d: Pen thickness (mm) [0—5 (0.3)] Pen Thickness
PT;
PU PU x1, y1(...,xn, yn); xn, yn: XY coordinates [*1] Tool Up
PU;
RA RA x, y; x, y: Absolute XY coordinates of opposite angle of rectangle [*1] Shade Rectangle Absolute
RR RR ∆ x, ∆ y; ∆ x, ∆ y: Relative XY coordinates of opposite angle of rectangle [*1] Shade Rectangle Relative
SA SA; None Select Alternate Set
SC SC Xmin, Xmax, Ymin, Xmin, Ymin: User XY coordinates of P1 [*1] Scaling
Ymax; Xmax, Ymax: User XY coordinates of P2 [*1]
SC;
SI SI w, h; w: Character width (cm.) [-128 — +127.99999 (3.8)] Absolute Character Size
SI; h: Character height (cm.) [-128 — +127.99999 (5)]
SL SL tanØ; tanØ: Character slant [*1 (0)] Character Slant
SL;
SM SM s; s: Character or symbol [*4 (Default: Clears symbol mode)] Symbol Mode
SM;
SR SR w, h; w: Character width (%) [*1 (3.8 )] Relative Character Size
SR; h: Character height (%) [*1 (5 )]
SS SS; None Select Standard Set
TL TL lp(,lm); lp: Tick length in positive direction [*2 (0.5%)] Thick Length
TL; lm: Tick length in negative direction [*2 (0.5%)]
UC UC (c,) ∆ x, ∆ y,(c,) c: Tool control value [-(67108863) — -99, +99 — +(67108863)] User Defined Character
,...., ∆ xn, ∆ yn; ∆ xn: Units of movement in X-axis direction [-99< ∆ xn<+99]
UC; ∆ yn: Units of movement in Y-axis direction [-99< ∆ yn<+99]
VS VS v; v: Tool speed (cm/sec.) [1 — 20 ] Velocity Select
VS;
WG WG r, Ø1, Øc(,Ød); r : Radius [*1] Ø1 : Start angle [*3] Shade Wedge
Øc : Center angle [*3] Ød : Chord tolerance [*3 (5 ° )]
XT XT; None X-Tick
YT YT; None Y-Tick