RCA DRC300iH - Manual (Page 2)

Playing a Disc
1. Press the STANDBY / ON button to turn on the unit.
See CUSTOMIZING THE FUNCTION SETTINGS before proceeding to step 2.
2. Press the OPEN/CLOSE button to open the disc tray.
3. Place a disc onto the disc tray with the label side up.
4. Press the OPEN/CLOSE button to close the disc tray. It takes a short while for your unit to load
the disc. After loading, for most DVDs, the unit will automatically take you main menu or start
playing.
5. If the unit does not automatically start playing the DVD, press the PLAY button.
Pausing Playback (Still Mode)
Press the PAUSE button on the remote. Each time you press the PAUSE button, the picture
advances one frame. To resume normal playback, press the PLAY button.
Stopping Playback
• Press the STOP button at the spot where you want to interrupt playback. To resume playback
at the spot where the disc was stopped, press the PLAY button.
• If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY
button will reset the disc to the beginning.
Fast Forward / Fast Reverse
1. Press the SEARCH or SEARCH button when a disc is playing. Each time you press the
SEARCH or SEARCH button, the playback speed changes in the following sequence:
2. Press the PLAY button when you reach the desired point to resume normal playback
Note:
• The unit mutes sound and subtitles during reverse and forward scan of DVDs.
• The fast playback speed may differ depending on the disc.
Skipping to a Different Chapter/Title
• Press the PREV button to go back to current or previous chapters/tracks.
• Press the NEXT button to advance chapters/tracks.
• For audio CDs, use the number buttons on the remote control to jump immediately to the desired
track number.
Slow-motion Play
1. Press the SLOW button on the remote in play
mode.
• Each time the SLOW button is pressed, the
speed of slow-motion playback changes in
the following sequence:
2. Press the PLAY button to return to normal playback speed.
Audio Selection
On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select
the preferred language and sound system.
1. While a disc is playing, press the AUDIO button to
show the current audio format (eg 5.1 or 2 channel).
2. Press the AUDIO button repeatedly to select the desired audio format.
Note:
• If only one audio format is recorded on the DVD, the AUDIO button becomes an invalid key and
will be displayed.
• Some DVDs allow you to change audio selections only via the disc menu. If this is the case, press
the MENU button and choose the appropriate language on the disc menu.
• You can select different audio channels (Stereo, Mono L, Mono R or Mix Mono) on an Audio CD
by pressing the AUDIO button repeatedly.
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as
shown in the example.
2. Press the SUBTITLE button repeatedly to select the
desired subtitle language.
Note:
• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear immediately after you select your desired
scene.
• The number of subtitle languages recorded differs depending on the disc. If only one language is
recorded, the language does not change.
• This function can only be used for discs on which subtitles have been recorded in multiple
languages.
• Some DVDs allow you to change subtitles only via the disc menu. If this is the case, press the
MENU button and choose the appropriate subtitle on the disc menu.
Angle Selection
Some DVDs contain scenes which have been shot
from a number of different angles. For these discs,
the same scene can be viewed from each of these
different angles.
1. While you are playing a DVD with different angles
recorded, press the ANGLE button to view the
number of current angles available.
2. Press the ANGLE button repeatedly to change the
scene to the next recorded angle.
• After approx. two seconds, playback will continue from the new angle you selected.
• If no button is pressed within 10 seconds, playback continues without changing the current
angle.
Note:
• This function can only be used for discs on which scenes shot from multiple angles have been
recorded.
• If only one angle is recorded, “ OFF ” is displayed.
Playing Videos
1. In iPod/iPhone Home menu, use the / button to
select Videos and press the OK button.
2. Use the / button to select from Movies, Music
Videos, TV Shows, Video Podcasts or Rentals,
press the OK button to enter. (“Navigate your iPod/
iPhone Video Library directly from your iPod/iPhone”
may appear on the screen if your are using an iPod
Touch.)
3. Use the / button to navigate the iPod/iPhone
menu lists and select a video, press the OK button
to begin playback. (You may also use the control wheel and keys on your iPod/iPhone to
operate it.)
• Press the PAUSE button to pause, press the PLAY button to resume.
• Press the / button to skip to the previous / next movie.
• Press the / button to begin fast reverse/forward, press the PLAY button to
resume normal playback.
4. Press the RETURN button to go back to the previous menu.
Note : Make sure TV Out in iPod is set to ON when you are playing the video.
Settings
1. In iPod/iPhone Home menu, use the / button to
select Settings and press the OK button.
2. Use the / button to select from Shuffle, Repeat
or Lanuage. Press the OK button to enter the
settings.
3. Use the / button to a setting, press the OK
button to confirm.
4. Press the RETURN button to go back to the previous
menu.
• Shuffle : Select from Shuffle Off, Shuffle Songs
and Shuffle Albums.
• Repeat : Select from Repeat Off, Repeat One and Repeat All.
• Language : Select OSD language.
WARNING: Due to the iPod/iPhone limitation, not all functions of some iPod/iPhone models can
be controlled via the remote control.
If the above screen appears, you may need to control the iPod Library directly from your iPod/
iPhone.
Note
If your iPhone is called while it is docked, playback will be paused.
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Using an iPod Touch to view photos
1. In iPod Home menu, use the / button to select Photos and press the OK button. “Navigate
your iPod Photo Library directly from your iPod” will appear on the screen.
2. Touch the “Photos” selection on iPod panel, and then select the photo your prefer.
3. Touch the “ ” to confirm the photo.
4. Depending on the video output setting of your iPod, you may need to tap “yes” on your iPod
screen to activate iPod’s video output.
5. Press RETURN button to end the photo viewing and go back to the previous menu.
Using an iPod Classic / iPod Nano to view photos
1. In iPod Home menu, use the / button to select Photos and press the OK button. “Navigate
your iPod Photo Library directly from your iPod” will appear on the screen.
2. Press the / button to select “Photos”, and then press the OK button to confirm.
3. Use the button to select a photo, press the OK button to begin playback.
4. Press OK button twice to activate photo showing to TV screen.
5. Press RETURN button to end the photo viewing and go back to the previous menu.
6. Press the CLEAR button to exit Photo Mode.
Note:
Make sure video out is activated in the setting of iPod Classic or iPod
Nano.
Connecting your iPod/iPhone
1. Insert your iPod/iPhone into the connector in the dock.
2. Press the SOURCE button to select iPod/iPhone mode, the iPod/iPhone Home menu
appears. Your iPod/iPhone will connect automatically within a few seconds.
Note:
• Your iPod/iPhone will be charged automatically (until fully charged) once it is connected, no
matter whether the unit is in iPod/iPhone mode or not.
Playing Music
1. In iPod/iPhone Home menu, use the / button to
select Music and press the OK button.
2. Use the / button to select from Playlists, Artists,
Albums, Songs, Genres or Composers. Press the
OK button to enter.
3. Use the / button to navigate the iPod menu
lists and select songs, press the OK button to begin
playback. (You may also navigate using your iPod
screen after pressing CLEAR key to activate the
menu on the iPod screen.)
• Press the PAUSE button to pause, press the PLAY button to resume.
• Press the / button to skip to the previous / next song.
• Press the / button to begin fast reverse/forward, press the PLAY button to
resume normal playback.
• Press REPEAT DISC button to select a repeat playback mode (a single repeat or all songs
repeat). Press again repeatedly to cancel this repeat playback.
4. Press the RETURN button to go back to the previous menu.
Note:
• You can use the / button to quickly navigate menu lists one screen at a time.
Playing Photos
1. In iPod/iPhone Home menu, use the / button to select Photos and press the OK button.
“Navigate your iPod Photo Library directly from your iPod” will appear on the screen.
2. Please use the control on your iPod/iPhone to operate.
• Press the PAUSE button to pause, press the
PLAY button to resume .
• Press the / button to skip to the previous /
next photo.
3. Press the RETURN button to go back to the previous
menu.
4. Press the CLEAR button to exit Photo Mode.
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a chapter
You can play the same chapter repeatedly.
1. While the disc is playing, press the REPEAT DISC button until the REP: [ CHAPTER ]
indicator displays on the screen. The current chapter is played repeatedly.
Repeating a title
You can play the same title repeatedly.
2. While the disc is playing, press the REPEAT DISC button until the REP: [ TITLE ] indicator
displays on the screen. The current title is played repeatedly.
To resume normal playback
3. While the disc is playing, press the REPEAT DISC button until the REP: [ OFF ] indicator
displays on the screen.
You can play a single track and whole disc repeatedly.
Repeating a single track
You can play the same track repeatedly.
1. While the disc is playing, press the REPEAT DISC button until the REP: [ REP 1 ] indicator
displays on the screen. The current track is played repeatedly.
Repeating a whole disc
2. While the disc is playing, press the REPEAT DISC button until the REP: [ REP ALL ]
indicator displays on the screen. The whole disc is played repeatedly.
To resume normal playback
3. Press the REPEAT DISC button until the REP: [ OFF ] indicator displays on the screen.
You can play a specific section repeatedly.
Repeating a specific section
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section
(REPEAT A- is displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section ( REPEAT A-B is displayed).
3. The unit will immediately begin replaying your selection.
To resume normal playback
4. While the disc is playing, press the REPEAT A-B button until the A-B CANCEL indicator
displays on the screen.
Note:
• Some discs may not permit A-B repeat operation.
• A-B repeat can only be used within the same title. If the start and end of the section to be
repeated are in different titles, A-B repeat is cancelled.
• You can specify a segment only within the current title or track.
• The A-B repeat function does not operate in scenes where different camera angles are
recorded.
Playing a Disc
This user manual explains the basic instructions for operating this unit. Some DVDs are
produced in a manner that allows specific or limited operation during playback. Therefore, this
unit may not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to
the instructions accompanying the specific DVD in question for more information about the
options available on that DVD.
may appear on the screen during operation. It means that the desired operation is not
permitted by the unit or disc.
There are four options in the main setup menu: System Setup, Language Setup, Audio Setup
and Video Setup.
In DVD mode, press SETUP to bring up the main menu. Select one of the menu icons across the
top of the screen using the or buttons. The menu’s options are displayed on the left side of
the screen. Press the , , or buttons to move to the option’s choices on the right. Then
press OK to select. Press SETUP or RETURN if you want to exit.
SYSTEM SETUP
1. Press the SETUP button in DVD mode.
2. Select System Setup in the main menu using the , , or
buttons.
3. Select a menu option using the or buttons and press OK
button.
VIDEO OUTPUT (HD OUTPUT / ANALOG VIDEO)
This allows to you pick the video output and video resolution that best suits your TV’s capabilities.
Note: Not all video outputs are operational for all video settings – the Composite Video
Out (YELLOW jack) is active for all video settings – we STRONGLY recommend you
connect this jack to your TV using the AV cable (included with this product), even if
you intend to use a different connection for normal viewing. If you find you lose video
by enabling a particular unsupported setting when using a connection other than
Composite Video Out – simply switch your TV to the AV input that you’ve connected
the AV cable to, then continue with your Video Menu setup activity.
If using digital HDMI connection (recommended), you should pick the resolution (480p, 720p,
1080i, 1080p) that matches the capabilities on your TV.
If using analog video connection - Composite Video (AV), S-Video, or Component Video - you
must select 480p resolution under HDMI settings. There are three analog video settings:
INTERLACE-YUV : Select if you are connecting the player with Component Video outputs to a
non-Progressive Scan TV.
P-SCAN YPbPr : Select if you are connecting the player with Component Video outputs to a
Progressive Scan TV.
S-VIDEO : Select if you are connecting the player with S-VIDEO output to a TV with
S-VIDEO input
TV TYPE
Depending on the format of the DVD, you can choose the picture format (aspect ratio) best
suited to the format of your TV screen:
4:3 PS (Pan Scan)
• When wide-screen video is played, this mode clips the right and left
sides of the image so that it can be viewed on a conventional screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback are
automatically played in letterbox mode (black bands top and bottom).
4:3 LB (Letter Box)
• When wide-screen video is played in this mode on a conventional
Analog TV, black bands appear at the top and bottom of the screen.
16:9 (Wide screen)
• This is the correct mode for playing wide-screen videos on on a wide-
screen TV (most modern Digital TV’s).
Note :
• The displayable picture size is determined by the DVD disc. Therefore
the playback picture of some DVD discs may not conform to the picture
size you select.
• When you play DVD discs recorded in the 4:3 aspect ratio, the playback
picture will always appears in the 4:3 aspect ratio regardless of the TV
TYPE setting.
DEFAULT
It takes 3-5 seconds to reset the unit to the factory default.
LANGUAGE SETUP
1. Press the SETUP button in DVD mode.
2. Use button to select Language Setup.
3. Use , , or button to select a language, then press
the OK button. The screen will change to your selected
language immediately.
4. To exit the SETUP MENU and return to the normal screen,
press the RETURN or SETUP button.
Note:
• Some DVDs may not play in the audio language selected.
A prior language may be programmed on the disc.
• Some DVDs may be set to display subtitles in a language other than the one you selected. A
different subtitle language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate subtitle language from the selection on
the disc menu.
• Some DVDs may not include your pre-selected language. In this case, the DVD player
automatically displays disc menus consistent with the disc’s initial language setting.
AUDIO SETUP
1. Press the SETUP button in DVD mode.
2. Select Audio Setup in the main menu using the or
buttons.
3. Select a menu option using the , , or buttons and
press OK button.
DIGITAL AUDIO
Select the Digital Audio Output format that matches your audio system’s capabilities. If your audio
system supports Dolby Digital (surround sound), you should select “RAW DVD FORMAT” setting. If
your system only supports Stereo (or if you’re using your TV’s stereo speakers for audio playback),
then you select “PCM (STEREO)” setting. Note, you’ll only experience full surround sound if you
use the COAXIAL Digital Audio output, and have selected “RAW DVD FORMAT” setting.
Please also note that not all DVD’s have surround sound audio tracks.
• If using HDMI connection to TV for Video AND Audio playback, you should select “PCM
(STEREO)” setting, so as to ensure a stereo (not surround sound) signal is passed to your
TV’s speakers.
VIDEO SETUP
1. Press the SETUP button in DVD mode.
2. Select Video Setup in the main menu using the or
buttons.
3. Select Brightness, Contrast, Hue, Saturation or Sharpness
using the or buttons, highlight your selections and
press OK button.
Playing Picture File Disc
Programmable memory
Locating a specific chapter / track
If you know the chapter / track number you want to play, you can locate a specifc chapter / track
by directly selecting a chapter / track number.
1. Press the GOTO button to search your
desired chapter / track.
2. Press or button to highlight a chapter /
track and press the corresponding number
button(s) for the chapter you want.
3. Press the OK button to confirm. The unit will start playback about 3 seconds later.
Locating a specific title
If a DVD disc contains title numbers, you can locate a specific title by directly selecting a title
number.
1. In stop mode, press the GOTO button.
2. Press or button to highlight a specific field and press the corresponding number button(s)
for the title you want.
3. Press the OK button to confirm. The unit will start playback about 3 seconds later.
Locating a specific time
You can move to a specific location by entering its corresponding time (hours, minutes,
seconds)
1. Press the GOTO button.
2. Press or button to highlight time.
3. Press the corresponding number buttons for the setting point you want.
4. Press the OK button to confirm. The unit will start playback about 3 seconds later.
Note :
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the
DVD disc.
rePeat PlaybacK
The two types of programmed playback provided by this unit are title/chapter programmed
playback and track programmed playback.
Title / Chapter programmed playback
1. Press the MEMORY button.
2. Enter the title numbers in . Use button to move the
highlight to chapter and enter the chapter numbers in .
3. Use , , or button to move to the other field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed
playback.
Note: If you press the STOP button twice, the programmed selection will be cleared.
Track programmed playback
1. Press the MEMORY button.
2. Enter the track numbers in .
3. Use , , or button to other field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed
playback.
This unit can play picture files recorded on CD-R and CD-RW discs.
Playing a Picture File Disc
1. Open the disc door.
2. Place a picture file disc onto the tray with label side up.
3. Close the disc door.
4. The unit will load the disc and automatically display the
contents of the disc on the screen, while playing the
beginning of the first picture file. These files will then be
played back one by one.
5. Press or button to select a picture file to view.
6. Press the , , or CURSOR button to view and select
the files that you want to view, then press the OK button to confirm the selected file.
Note:
• You can press the PAUSE button to interrupt playback, and press the PLAY button to
resume playback.
• You can use the GOTO function or use the numbered buttons to enter the number of a picture
file to quickly select the image.
• Press the ANGLE button on the remote control to rotate the picture orientation by 90°.
Folders Files within the
current folder
locating a DesireD section
Please Navigate directly on your iPod
OR
Press The [CLEAR] Key
to go back to main menu
customiZing the Function settings
Zooming into an image
While a disc is playing, press the ZOOM button repeatedly to enlarge the image in several levels.
• While an image is zoomed, you can use the , , or CURSOR button to shift the view
and display the part you want.
• To return to normal view, press the ZOOM button until the “ZOOM: OFF” shows. The screen
will return to normal.
• When you reach the edge of the image, the display will not shift anymore in that direction.
Step 2 Step 3 Step 4
Step 2 Step 3 Step 4
Display Function
While the disc is playing, press the DISPLAY button on the remote control repeatedly to display
information on operation status.
e.g.
Specifications and external appearance are subject to change without notice.
-
T
C
-
T 02:01:22
00:30:15
00:12:03
Chapter Remaining time
Total time
Title Elapsed time
Elapsed Time:
Elapsed time from the beginning of the
chapter/title which is currently playing.
Remaining Time:
Remaining time of the chapter/title
which is currently playing.
6 7 10 9 8
iPod/iPhone Features
SF 1/2 SF 1/3 SF 1/4 SF 1/5
PLAY SF 1/7 SF 1/6
e.g.
or
Play ForWarD x2 ForWarD x4
ForWarD x8 ForWarD x20
Play bacKWarD x2 bacKWarD x4
bacKWarD x8 bacKWarD x20
WIDE SCREEN
LETTER BOX
PAN SCAN
Cut off when a wide-
screen video image is
played.
Docking System for iPod
iPod
Home
Music
Photos
Videos
Settings
Docking System for iPod
iPod
Home
Music
Photos
Videos
Settings
Docking System for iPod
iPod
Home
Music
Photos
Videos
Settings
Docking System for iPod
iPod
Home
Music
Photos
Videos
Settings
Printed in China 811-793091W010
DRC300iH eng ib.indd 2 10/6/2009 9:45:27 AM