Speciﬁcations safety, Important safety instructions, Speciﬁcations – Radio Shack 32-2054 User Manual

Page 9: Care and maintenance, Replacing the dc power cord’s fuse

Speciﬁcations

Output Power (at THD 10%, 4 Load 1kHz)..................................................40W
Total Harmonic Distortion (at 5 Watts, 4, 1kHz, with Band Pass Filter)

MIC ......................................................................................................... 0.50%
AUX ......................................................................................................... 0.10%
PHONO .................................................................................................. 0.30%

Input Sensitivity (at 10%, THD, 1kHz)

MIC ........................................................................................................2.5 mV
AUX .......................................................................................................150 mV
PHONO .................................................................................................3.5 mV

Signal to Noise Ratio with A-WTD

MIC ..........................................................................................................60 dB
AUX ..........................................................................................................80 dB
PHONO ...................................................................................................70 dB

Hum and Noise at 4

At MASTER VOLUME MIN......................................................................1 mV
At MASTER VOLUME MAX ..................................................................50 mV

Power Supply ..............................................................120V AC, 60Hz; or 12V DC
Dimensions (W×D×H) .......................... 12.8 Ч 8.9 Ч 3.3 in (324 Ч 226 Ч 85 mm)

Speciﬁcations are subject to change and improvement without notice. Actual product
may vary from the images found in this document.

Care and Maintenance

• Keep the ampliﬁer dry; if it gets wet, wipe it dry immediately.
• Use and store the ampliﬁer only in normal temperature environments.
• Handle the ampliﬁer carefully; do not drop it.
• Keep the ampliﬁer away from dust and dirt, and wipe it with a damp cloth

occasionally to keep it looking new.

• Modifying or tampering with the ampliﬁer’s internal components can

cause a malfunction and might invalidate its warranty. If your ampliﬁer
is not performing as it should, take it to your local

RadioShack store for

assistance.

Replacing the DC Power Cord’s Fuse

If the ampliﬁer does not operate from a 12V battery source, check the fuse in
the DC power cord plug. If the fuse is blown, remove the cap of the plug and
replace the fuse with one of the proper type and rating (6A, 250V).

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Clean only with dry cloth.

Only use attachments/accessories speciﬁed by the manufacturer.

Do not use this product near water.

Use only with the cart, stand, tripod, bracket, or table speciﬁed by the
manufacturer or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.

Exercise caution when moving any product and cart combination. Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.

10. Slots and openings in the cabinet are provided for ventilation and to ensure

reliable operation of the product and to protect it from overheating. Do not block
any ventilation openings. Install in accordance with the manufacturer’s instructions.

11. Use only the type of power source indicated on the label. If you are not sure of the

type of power supply to your home, consult your product dealer or local power
company. For products intended to operate on battery power, or other sources,
refer to the operating instructions.

12. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not ﬁt into your
outlet, consult an electrician for replacement of the obsolete outlet.
Alternate Warnings: This product is equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only ﬁt into a grounding-
type power outlet. This is a safety feature. If your are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the grounding-type plug.

13. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

14. Protective Attachment Plug: The product is equipped with an attachment

plug having overload protection. This is a safety feature. See Instruction Manual
for replacement or resetting of protective device. If replacement of the plug is
required, be sure the service technician has used a replacement plug speciﬁed by
the manufacturer that has the same overload protection as the original plug.

15. If an outside antenna is connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure,
grounding of the mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode.

16. Unplug this apparatus during lightning storms or when unused for long periods of

time.

Speciﬁcations

Safety