RCA RT2906 - Manual

It's important to read this instruction prior to using your new product for the first time. 811-AV6291W111
RT2906
www.RCAav.com
Printed in China
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna. •
Increase the separation between the equipment and receiver. •
Connect the equipment into an outlet on a circuit different from that to which the receiver is •
connected.
Consult the dealer or an experienced radio / TV technician for help. •
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment
Regulations.
The Shock Hazard Marking and Associated Graphical Symbol is provided on the bottom panel of unit.
Refer to the identification / rating label located on the back panel of your product for its proper
operating voltage.
IMPORTANT: The power cord can be unplugged to turn off the main power to the unit. It should also be
easily accessible in an emergency.
Leave sufficient space around the appliance to allow adequate ventilation: 10cm on either side and •
at the back, as well as 7cm above it are ideal.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Connections and Setup Connections and Setup Connections and Setup
Connections and Setup Connections and Setup Connections and Setup
FCC Information FCC Information
Important Safety Instructions
Positioning Speakers
For Your Safety
The AC power plug is polarized (one blade is wider
than the other) and only fits into AC power outlets
one way. If the plug won’t go into the outlet
completely, turn the plug over and try to insert it
the other way.
If it still won’t fit, contact a qualified electrician to
change the outlet, or use a different one. Do not
attempt to bypass this safety feature.
CAUTION:
To prevent electric shock, match wide blade of •
plug to wide slot, fully insert.
The apparatus shall not be exposed to dripping •
or splashing and that no objects filled with
liquids, such as vases, shall be placed on
apparatus.
The mains plug is used as disconnect device. •
The mains plug of apparatus should not be
obstructed OR should be easily accessed during
intended use. To be completely disconnect the
power input, the mains plug of apparatus shall
be disconnected from the mains.
Service Information
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this user
manual.
Connecting for Power
Make sure you connect all your other electronic
components and the speakers before plugging
your unit into the outlet. Plug the power cord in
the wall outlet, matching the wide blade of the
plug with the wide slot in the outlet. Be sure to
insert the plug completely.
Technical Specification
Product: Dolby Digital Audio / Video Receiver
Brand: RCA
Electrical Consumption
Power Supply: 120V ~ 60Hz
This Home Theater has earned
the ENERGY STAR.
Headset Safety
Do not play your headset at a high volume. •
Hearing experts warn against extended high-
volume play.
If you experience a ringing in your ears, reduce •
volume or discontinue use.
You should use extreme caution or temporarily •
discontinue use in potentially hazardous
situations.
Even if your headset is an open-air type •
designed to let you hear outside sounds, don't
turn up the volume so high that you are unable
to hear what is around you.
Excessive sound pressure from earphones and •
headphone can cause hearing loss.
THE LIGHTNING FLASH AND ARROWHEAD
WITHIN THE TRIANGLE IS A WARNING
SIGN ALERTING YOU OF “DANGEROUS
VOLTAGE” INSIDE THE PRODUCT.
THE EXCLAMATION POINT WITHIN THE
TRIANGLE IS A WARNING SIGN ALERTING
YOU OF IMPORTANT INSTRUCTIONS
ACCOMPANYING THE PRODUCT.
Please read and save for future reference.
Some of the following information may not apply
to your particular product; however, as with
any electronic product, precautions should be
observed during handling and use.
Read these instructions. •
Keep these instructions. •
Heed all warnings. •
Follow all instructions. •
Do not use this apparatus near water. •
Clean only with a dry cloth. •
Do not block any ventilation openings. •
Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such •
as radiators, heat registers, stoves, or other
apparatus (Including amplifiers) that produce
heat.
Do not defeat the safety purpose of the •
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety.
If the provided plug does not fit into your wall
outlet, consult an electrician for replacement of
the obsolete outlet.
Protect the power cord from being walked on •
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments / accessories specified by •
the manufacturer.
Use only with a cart, stand, tripod, bracket or •
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart / apparatus combination
to avoid injury from tip-over.
Unplug this apparatus during lightning storms •
or when unused for long periods of time.
Refer all ser vicing to qualified ser vice •
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as the power cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Additional safety information
• Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
• Always leave sufficient space around the product
for ventilation. Do not place product in or on a bed,
rug, in a bookcase or cabinet that may prevent air
flow through vent openings.
• Do not place lighted candles, cigarettes, cigars,
etc. on the product.
• Connect power cord only to AC power source as
marked on the product.
• Care should be taken so that objects do not fall
into the product.
• Do not attempt to disassemble the cabinet. This
product does not contain customer serviceable
components.
If your product operates on batteries, adhere to
the following precautions:
A. Any battery may leak electrolyte if mixed with a
different battery type, inserted incorrectly, or if
all batteries are not replaced at the same time.
B. Any battery may leak electrolyte or explode if
disposed of in fire or an attempt is made to charge
a battery not intended to be recharged.
C. Discard leaky batteries immediately. Leaking
batteries can cause skin burns or other personal
injury. When discarding batteries, be sure to
dispose of them in a proper manner, according
to your state / provincial and local regulations.
D. Battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
]
Portable Cart
Warning
• One main unit
• One remote control with batteries
• One pair of front speakers, one pair of rear speakers,
one center speaker and one subwoofer
• One pig-tail antenna wire
• One AM loop antenna
• One coaxial digital cable
• One pair of audio cable for analog connections
• One English & one Spanish user manuals
• One English & Spanish quick start guides
Setup and Maintenance of the Unit
Provides spaces for sufficient ventilation as
indicated:
• Do not connect to the AC power cords until all
connections are completed.
• Do not use your set immediately after transferring
it from a cold place to a warm place: there is risk
of condensation.
• Do not expose your set to water and excessively
high temperatures.
• After having disconnected your set, clean the
case with a soft cloth, or with a slightly damp
leather chamois. Never using strong solvents.
Protect your Components from
Overheating
• Do not block ventilation holes in any component.
Arrange the components so that air can circulate
freely.
• Do not stack components directly on top of each
other.
• Do not place the unit near other components
that generate heat such as heating vents.
• Allow adequate ventilation when placing your
components in a stand.
• Place an amplifier near the top shelf of the stand
so heated air rising from it will not affect other
components. If you have a satellite receiver, you
should place it on the top shelf. AM loop antenna
Connecting to HDMI Components
Connecting to Audio Components
3
3
1
1
2
4
Courtesy Dolby Laboratories
1. Left, Right (Front Speakers)
Front speakers carry primarily music and sound
effects.
2. Center
In surround mode, the center speaker carries most
of the dialog as well as music and effects.
It should be set between the left and right
speakers.
3. Surround (Rear Speakers)
The surround speakers’ overall sound balance
should be as close as possible to the front speakers.
Proper placement is vital to establish an evenly
distributed sound field.
4. Subwoofer
A subwoofer is designed to reproduce powerful
low bass effects (explosions, the rumble of
spaceships, etc.).
Magnetic Shielding
Speakers placed less than two feet from the TV set
must be magnetically shielded in order to prevent
picture distortion. Center speaker provided with
this unit is magnetically shielded to protect your
TV set.
Front Speaker Placement
For best results, follow the speaker placement
below.
Alignment
Align the center speaker evenly with (A) or slightly
behind (B) (the left and right speakers), but not
ahead of them.
Angle
Place the left and right speakers to form a 45-
degree angle with your favorite viewing position
to duplicate the soundtrack mixer’s perspective.
Height
The three front speakers should be as close as
possible to the same height. This often requires
placing the center speaker directly on top (A) or
beneath (B) the TV set.
A
B
Courtesy Dolby Laboratories
Courtesy Dolby Laboratories
Courtesy Dolby Laboratories
Courtesy Dolby Laboratories
Better Surround Placement
Location
If possible, place surround speakers to either side of the listening area, not behind it.
Height
If space permits, install surround speakers 2-3 feet above viewers. This helps to minimize localization
effects.
Aiming
Aim surround speakers straight across the room, not down at viewers, to help create a more open, spacious
surround sound field.
Alternative Surround Placement
Rear wall
If rear wall mounting is the only choice, aim the speakers at each other (A), towards the front (B) or towards
the sidewalls (C, D).
Experiment with placement until sounds seem to surround you, rather than come from behind you.
No adjacent walls
Surround speakers can go on stands facing each other to approximate sidewall mounting (A), or to the
sides or rear of the viewing area, aimed upwards; they can go right on the floor, or preferably, a few feet
off the floor such as on end tables (B).
User Manual
- 1 -
- 9 - - 8 - - 7 - - 10 -
- 5 - - 4 - - 3 - - 6 -
- 2 -
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Digital Connection
The digital audio jacks can accept Dolby Digital (Surround Sound) or PCM (Stereo) signals when
compatible components are connected.
• This unit provides one optical and one coaxial digital input jacks for the connection of your
components that have digital audio outputs.
• To connect DVD player, Satellite receiver, Cable box, Blu-ray player or TV that has a digital audio
output, use a coaxial digital (included) or an optical digital cable (not included) to carry the audio
signal and enjoy Dolby Digital sound quality.
• A separate optical or coaxial cable is needed for each digital connection.
Notes: • If your TV has digital audio output, you can connect it to the corresponding digital
audio input of the system instead of using analog connection.
• Optical and coaxial cables carry only the audio portion of the signal.
User manual
Digital Audio in Connection
ANALOG AUDIO IN
Unit Controls
Main Unit
1. / (TUNING buttons)
Tunes in to desired stations in AM/FM mode.
2. ON/STANDBY
Turns on / off the unit. When the unit is turned on, the unit will go to the mode it was in before powered
off.
3. / (PRESET buttons)
Selects preset stations in AM/FM mode;
Selects item to be set in SETUP MENU.
4. GAME jacks
Connects game consoles or other AV products that have AUX audio outputs.
5. LINE IN
Connects portable audio devices or other AV products that have a LINE-OUT jack.
6. / (SURROUND buttons)
Selects among digital surround sound effects. (HALL, CHURCH, CLUB, STADIUM, STUDIO, STEREO, DOLBY
PL EMULATION, DOLBY PL II MUSIC, DOLBY PL II MOVIE) depending on input signal.
Adjusts value in SETUP MENU.
7. DVD, TV, SAT-CABLE, AM/FM, VCR, BD and GAME/LINE-IN (SOURCE buttons)
Selects sound source.
8. Headphone jack
9. MASTER VOLUME
Adjusts the volume.
10. SETUP
Enters or quits the SETUP menu.
1
3
8 7 6 5 4
9
10
2
Blu-ray Disc Player
Analog Audio
Signals
Analog Audio
Signals
Satellite Receiver or Cable Box
TV with HDMI Input
Optical Digital In (Audio)
Connect to optical digital output of Cable box, Satellite receiver, DVD, Blu-ray player,
TV or other compatible devices using the Optical Fiber Cable (not included).
Coaxial Digital In (Audio)
Connect to coaxial digital output of DVD, Cable box, Satellite
receiver, TV or other compatible devices using the Coaxial Digital
Cable (included).
BD/DVD/SAT-CABLE/TV/GAME
BD/DVD/SAT-CABLE/TV/GAME
DVD player
Connecting the speakers
Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each
speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the
terminal and insert the wire. Release the tab to lock wire in the terminal.
When connecting the speakers, make sure the polarities (“+“ speaker wire to “+“ on the unit. For example,
red wire to red terminal on the unit) of speaker wires and terminals match.
If the cords are reversed, the sound will be distorted. Do not let the speaker wires touch each other, it will
damage the Home Theater’s amplifier.
Connecting the Antennas
Connect the AM and FM antennas to the AM and FM terminals on the system’s back panel.
They must be hooked up in order to receive clear reception. For FM reception, extend antenna to its full
length. For AM reception, rotate the antenna horizontally to get better reception.
FM
AM Loop Antenna and FM Indoor Antenna
1. Uncoil the antenna wire and locate the base end of the AM antenna.
2. Press down on the antennas tab to open the terminal.
3. Insert the antenna wires into the terminal and release the tabs to secure the wires in place.
4. Make sure the white wire on the AM loop antenna is inserted into the AM loop terminal and the other
wire is inserted into the ground loop terminal.
Digital Input
Connect components, such as DVD players, Satellite receiver/Cable boxes, BD (Blu-ray Disc TM ) players or TVs,
capable of outputting Dolby Digital (Surround Sound) or standard PCM (Stereo) format digital signals.
Note: “Blu-ray Disc” is a trademark of Blu-ray Disc Association.
This class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
Left and right
front speakers
Left and right
rear speakers
Note: This product will play audio from HDMI-connected products
while also passing on the video signal to a HDMI-connected TV.
Quick start
guide
Center
Speaker
Right Left
Rear Speakers
(Surround Sound)
Blue and Black Grey and Black
Purple and Black
White and Black Red and Black
Front Speakers
Green and Black
Use this jack on
the rear panel
to connect an
active subwoofer
other than the
one supplied.
SUBWOOFER AUDIO OUT
Subwoofer
Right Left
Center speaker
Coaxial digital
cable
Audio cable for
analog connections
Pig-tail
antenna wire
Remote
control with
batteries
BD
TV VCR DVD SAT/CAB
AM/FM GAME/LINE-IN
SOURCE
RCR192A B2