Identification of controls, Front panel – NAD T775 User Manual

Page 8

1 POWER BUTTON : Press this button or the HTR 3 remote’s [ON] button

to switch ON the T 775. The Standby LED indicator will turn from amber
to blue and illuminate the VFD. Pressing the power button again turns
the unit back to standby mode.

The T 775 can also be switched ON from standby mode by pressing

any of the front panel buttons. When both Main and Zones are ON,
press and hold this button for more than five seconds to place them at
standby mode.

NOTES:
• The rear panel POWER switch must be in the ON position for the Power

button to activate.

• If Auto Trigger IN at Trigger Setup menu is assigned to ‘Main’ or ‘All’ and

the TRIGGER switch is set to ‘AUTO’ mode, the Power button in the front
panel as well as the corresponding ON/OFF function keys in the HTR 3
remote control will be disabled effectively handing this function to an
external controller. Switch TRIGGER to ‘OFF’ to maintain normal power
ON/OFF function procedures. (See section also about “Trigger Setup”
under the “Setup Menu” discussions.

2 STANDBY LED : This indicator will light up amber when the T 775 is

in standby state. When the T 775 main or zones are in the ON state,
this indicator will illuminate blue. In the unlikely event that the T 775
switches to protection state, then this indicator will illuminate red.
When infrared command from the HTR 3 is received, this indicator will
also flash momentarily.

3 INFO : Repeatedly toggle this button (press/hold first if in Tuner mode

and then toggle) to display both at the Vacuum Fluorescent Display
(VFD) and On-Screen Display (OSD) the following – Current Source,
Volume level, Listening mode, Audio Source Format, and active Zones
with their corresponding Source Inputs. While at Tuner mode, toggle
this button to cycle through Preset Name, RDS name and RDS text.

4 AM/FM/DB : Toggle this button to select either AM, FM, DAB (Europe

version) or XM (North America version) tuner functions.

5 TUNER MODE : In FM mode, this button will toggle between FM

Stereo and FM mono. Select FM Mono (FM stereo and FM Mute icons
at VFD are extinguished) for stations that have too much interference
or are too weak. In DAB (Europe version) or XM (North America version)
radio, this button enables the digital radio menu in conjunction with
the Navigation button and Enter buttons.

6 MEMORY : Press this button to store tuned AM, FM and digital radio

stations to the T 775’s 40 preset-memory locations. One can store a mix
of any AM, FM and digital radio stations to the 40 available presets.

7. NAVIGATION and ENTER buttons : These buttons are used to

navigate the T 775 OSD, Tune Scan Forward

and Tune Scan Reverse

, Preset Skip Forward

and Preset Skip Reverse

as well as

navigation of DAB (European version), XM (North American version)
tuner functions and iPod.

8 VACUUM FLUORESCENT DISPLAY (VFD) : Provides visual

information on all of the T 775’s important modes, settings and function
for both Main and Zone locations.

9 VOLUME : Use this control to adjust the volume level of the main

speakers. The default volume level is -20dB. The VOLUME knob is also
used to increment / decrement other adjustable parameters like Tone
Controls.

10 A SPEAKERS B : Press either speaker A or B or both to select the

set of speakers you wish to listen to. Speaker A is the main set of 7
multichannel and surround speakers. Speaker B is an auxiliary set
for remote locations such as other rooms of your home. For Speaker
B selection, all surround sound sources are downmixed to stereo.
Combining Speaker A and Speaker B (SPEAKERS A + B) will also result to
the source being downmixed to stereo.

IDENTIFICATION OF CONTROLS

FRONT PANEL

LIS

LIA

РУ

СС