Identification of controls, Rear panel – NAD T 765 User Manual

Page 12

13 +12 V TRIGGER OUT : There are three configurable +12V TRIGGER

OUTPUT. Use a 3.5mm mini-jack connector to pass +12 volts at a
maximum current of 50 milliamps to auxiliary equipment such as a
multichannel amplifier or subwoofer. The center conductor (hot) of the
3.5mm jack is the control signal. The outside conductor (shield) is the
ground return-path.

TRIGGER IN accepts 12V Trigger output of compatible components

such as power controllers and home automation devices.

TRIGGER OFF/AUTO. When at AUTO position, the T 765 selects the 12V

Trigger Input to turn ON (if so assigned at the ‘Trigger Setup’ menu) and
at the same time disables the HTR 3 and front panel’s ON/OFF function.
When at OFF position, the trigger input is disabled.

WARNING

If Auto Trigger IN at Trigger Setup menu is assigned to ‘Main’ or ‘All’ and
the TRIGGER switch is set to ‘AUTO’ mode, the Power button in the front
panel as well as the corresponding ON/OFF function keys in the HTR 3
remote control will be disabled effectively handing this function to an
external controller. Switch TRIGGER to ‘OFF’ to maintain normal power
ON/OFF function procedures.

See discussion on ‘Trigger Setup’ at the ‘Setup Menu’ literature for

guidelines on how to configure TRIGGER IN/OUT.

14 IR IN/OUT : These mini-jacks accept and output remote-controlled

codes in electrical format, using industry-standard protocols, for use
with “IR-repeater” and multi-room systems and related technologies.

IR IN. This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow
control of the T 765 from a remote location.

IR OUT . When connected to the IR IN of an ancillary equipment,

direct the ancillary equipment’s own remote control to the T 765’s
infrared receiver to command or control the linked unit.

IR IN and IR OUT . Connect the T 765’s IR IN to the IR OUT of an

ancillary equipment. Connect also the T 765’s IR OUT 3 to another
equipment with IR IN feature. With this setup, the T 765 acts as an “IR-
repeater” allowing the equipment connected to the T 765’ s IR IN control
or command of the other equipment linked to the T 765’s IR OUT 3.

IR OUT 1. In conjunction with IR IN, IR OUT 1 can be used as an “IR-

repeater” just like the IR OUT 3 as described above. It can also stand
alone as an IR OUT similar to that of IR OUT 2 function.

All NAD products with IR IN/IR OUT features are fully compatible with

the T 765. For non-NAD models, please check with your other product’s
service specialists as to their compatibility to the T 765’s IR features.

15 ZONE 2, ZONE 3, ZONE 4 : Sends zone selected audio and video

output sources to the corresponding audio and video input of another
separate zone. Use high quality patch cables to reduce noise pickup
over long distance runs. For a better understanding of zone settings,
study below the section on ‘Zone Controls’ of the ‘Main Menu’ discussion
as well as the item on ‘Zone Setup’ under the ‘Setup Menu’ literatures.

NOTE

The ZR 4 remote control will only control Zone 2 applications. Zone 3
and Zone 4 could be configured and managed at the appropriate Zone
OSD menu using the front panel navigations buttons as well as the
corresponding keys on the HTR 3 remote control.

16 AUDIO PRE-OUT : The Audio PRE- OUT makes it possible to use the

T 765 as a pre-amplifier to external power amplifiers for some or all
channels. Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-
BL, SURR-BR and CENTER to the respective channel input of a power
amplifier or amplifiers driving the corresponding applicable speakers.

Unlike the full range channels, there is no power amplifier built-into the

T 765 for a subwoofer. Connect the SUBW 1 or SUBW 2 output or both
to powered (“active”) subwoofers or to power amplifier channels driving
a passive system.

NOTE

Never connect both the external amplifier and T 765’s speaker outputs to
the same set of speakers.

17 SPEAKERS A, SPEAKERS B : Connect the respective SPEAKER A’s

FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL, SURR-BR and
CENTER channels to their corresponding loudspeakers. Make sure
the “+” (red) terminal and “-“(black) terminal are connected to the
corresponding “+” and “-“terminals of the loudspeaker. Use extra care to
ensure that no stray wires or strands cross between posts or terminals at
either end.

Connect left and right channels of Speakers B to the corresponding

remote loudspeakers. When Speakers B is activated, the output is
converted to ‘Stereo Downmix’ as indicated in the VFD. Combining
Speaker A and Speaker B (SPEAKERS A + B) will also result to the source
being downmixed to stereo.

The T 765 is designed to produce optimum sound quality when

connected to speakers with impedances within its operating range.
Please make sure that all the speakers are rated 4Ω minimum per speaker.

NOTE

Use stranded wire of at least 16 gauge (AWG). Connections to the T 765
can be made with banana plugs (US model only) or by using bare wire
or pins. Use the transverse hole through the post for bare-wire or pin
connections. By loosening the terminal’s plastic nut, make a clean, neat
connection and re-tighten carefully. To minimize the danger of short-
circuit, ensure that only 1/2-inch of exposed wire or pin is employed
when connecting.

18 AC POWER INLET : Connect to the supplied IEC-standard removable

AC power cord or a compatible cord.

19 SWITCHED AC OUTLET : This convenience outlet can supply switched

power to another component or accessory. It is powered ON and OFF
by the front panel POWER SWITCH or by the HTR 3’s ON and OFF keys.

The total draw of all devices connected to this jack must not exceed 120

watts.

20 POWER : The POWER switch supplies the master AC mains power for

the T 765. When this switch is at ON position, the T 765 is in standby
mode as shown by the amber status condition of the standby LED. If
you intend not to use the T 765 for long periods of time (such as when
on vacation), switch the POWER switch to the OFF position. When the
POWER switch is at OFF position, the front panel power button, HTR 3
remote control or ZR 4 cannot activate the T 765.

IDENTIFICATION OF CONTROLS

REAR PANEL

LIS

LIA

РУ

СС