Nokia CC100 - Manual (Page 47)

CC100Master Bridge User’s Guide
44
snmptrapserver
[ -s
[ -c ]
[ -p ]
[ -a ]
[ -m ] ]
Display or set up SNMP trap server(s) configuration.
: trap server index, at most 5 servers (0~4)
: activate or de-activate trap server IP
: SNMP trap UDP port number (0~65535), default 162
: trap server IP address
: trap server community name, default ‘ public ’
snmptrapsetup
[ -l ]
[ -u ]
[ -s ]
[ -d ]
Enable or disable specified trap type,
: turn on or turn off this trap type, default is on
-l: logon/logoff trap
-u: upload/upgrade firmware/driver trap
-s: EP on-line status changed trap
-d: EP diagnosis trap
sntp
[ -c ]
[ -r ]
[ -z ]
[ -s -a address ]
Display or set up SNTP configuration for System Time .
: activate or de-activate SNTP service for system
time
: query SNTP server period, default 60 minutes
: ‘+ hh : mm ’ or ‘- hh : mm ’ to GMT time, hh for hours
and mm for minutes, default ‘ +00:00 ’
: 2 registered SNTP server set(0~1)
address: SNTP server host name or IP address in current set
stat
[ -r ] Display port statistics for port LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
swconfig
[ -p
[ -s
/100h /100f>] ]
Display or set up Ethernet port LAN1/LAN2 properties
: configure LAN1 or LAN2 port
: auto-negotiation mode
<10h/10f/100h/100f> : 10/100Mbps, half/full-duplex mode
swigmp
[ -c ]
[ -t
(4~510, even
number)>]]
Display or set up IGMP v2 snooping configuration
: enable or disable built-in IGMP v2 snooping function,
default is off
: expiry timer to age learned Multicast MAC if
no IGMP query frame received from the router, default is 248
seconds (range from 4 to 510 in even)
swqos
[ -q
[ -w ]
[ -d ]]
Display or set up the QoS configuration, include priority queue,
service weight and discard ratio while congestion, refer
Priority
for more.
: select queue index (0~3) to configure, as q0(lowest
priority)/q1/q2/q3(highest priority)
: assign the queue with service weight(1~15), default
1 for q0, 2 for q1, 3 for q2 and 4 for q3
: choose the discard mode(0~3) for queue
utilization, default 0 for 0%.
1 for 25%, 2 for 50% and 3 for 75%. refer Priority for more.
swqosrate
[ -p
[ -d ]
[ -c ]
[ -r
rate=N*64kbps)>] ]
Display or set up the LAN1/LAN2 maximum rate. refer
Bandwidth Control for more.
: configure LAN1 or LAN2 port
: direction, incoming(rx) or outgoing(tx)
: enable or disable control on this direction
: the setup max rate (multiply value by 64kbps). Range
from 0 to 1563, bandwidth control is invalid if N >= 1563
swqostc
[ -s
[ -c ]
[ -p
-q ] ]
Display or set up the QoS configuration for TCP/UDP traffic
classification, to assign higher priority for total 8 different
TCP/UDP protocols
: rule set index, at most 8 set (0~7)
: activate or de-activate this set
: TCP/UDP port number (0~65535),
: select queue index (0~3) for this rule set, as
q0(lowest priority)/q1/q2/q3(highest priority)
swsmac
[ -m ] Display or set up the static MAC entry, total 8 entries of MAC