NEC MT1045 - Manual (Page 23)

E–23
Setup
Orientation
Page1 Page2 Page3
Front Floor
Background
Blue
Signal Select
S-Video Auto
Video Auto
RGB1 Auto
RGB2 Auto
OK Cancel
Page4
Setup
Enables you to set operating options.
Press “OK” to save your changes for all the features of Page1, Page2,
Page3 and Page4.
[Page1]
Page4
Setup
Page1
Mouse
Button
Right Hand Left Hand
Auto Start
Page2 Page3
Power Management
Power Off Confirmation
Keystone Save
Clear Lamp Hour Mater
Fan High Speed Mode
OK Cancel
Sensitivity
Fast Medium Slow
Orientation:
This reorients your image for your type of projection.
The options are:front floor projection, rear ceiling projection, rear
floor projection, and front ceiling projection.
Background:
Use this feature to display a black, blue screen or logo when no
signal is available.
Transferring a logo from your PC
You can transfer your background logo from your PC to the projector.
To proceed as follows:
1) Install the PC Control Utility 1.0 on your PC from the supplied CD-
ROM. See page E-27 for installation.
2) Connect the PC CONTROL port of the projector with the serial
port of your PC with the supplied serial cable and then turn on the
projector.
3) Start the PC Control Utility on your PC.
4) Click "Logo Transfer" button.
For more detailed information, see Readme.txt file included on the
supplied CD-ROM.
NOTE: File size must be 64KB or less. JPEG and BMP images are
available only.
Signal Select:
Allows you to choose "RGB 1 or 2" for an RGB 1 or 2 source
such as a computer, or "Component" for a component video source
such as a DVD player. Normally select "Auto" and the projector
automatically detects a component signal. However there may be
some component signals that the projector is unable to detect. If
this is the case, select "Component".
This feature enables you to select composite video standards
manually. Normally select "Auto".
When you select the video standard for Video and S-Video sepa-
rately, first select the radio button and then select the video stan-
dard from the pull-down menu.
This must be done for Video and S-Video respectively.
[Page2]
Auto Start:
Turns the projector on automatically when the power cable is
inserted into an active power outlet. This eliminates the need to
always use the “Power” button on the remote control or projector
cabinet.
Power Management:
When this option is on and there is no RGB input for five min-
utes or more, the projector will automatically turn itself off.
Power Off Confirmation:
This option determines whether a confirmation dialog for turn-
ing off the projector will appear or not.
NOTE: When the confirmation message is displayed, you must be in the Pro-
jector mode to operate your projector using the remote control. If not, press
the Computer/Projector Select button to change your projector to the Projec-
tor mode. The button lights to indicate that you are in the Projector mode.
Mouse Settings:
This option lets you to change your USB mouse settings. The
mouse settings feature is available for USB mouse only. Choose
the settings you want:
Mouse Button: “Right Hand” or “Left Hand”
Mouse Sensitivity: “Fast”, “Medium” or “Slow”
Keystone Save:
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are
saved when you turn off the projector.
Fan High Speed Mode:
This option allows you to select two modes for fan speed: high-
speed mode and normal speed mode.
When you wish to cool down the temperature inside the projec-
tor quickly, check this box. This is convenient especially when
the projector is installed on the ceiling.
Clear Lamp Hour Meter:
Resets the lamp clock back to zero. Pressing this button appears
the “Clear Lamp Usage ?” confirmation dialog box. To reset the
lamp usage hour, press “OK”.
NOTE: The projector will turn off and go into standby mode after 2100
hours (1600 hours for MT1045) of service. If this happens, press the
“Help” button on the remote control for ten seconds to reset the lamp
clock back to zero. Do this only after replacing the lamp.