Pioneer PDR-609 - Manual (Page 30)

30
En
6 More recording features
If the disc is already named, the character
display shows the name (or the first 12
characters if it is too long to be displayed
completely), with a blinking cursor under
the first character.
4 Select/change the character at
the current cursor position by
turning the jog dial.
See below for the complete list of letters,
numbers, and symbols available.
If you’re using the remote control, use
numbers keys 1-9 for numbers and the
letters shown above each key. Press a key
repeatedly to cycle through the letters and
numbers on that key.
Characters available for disc and track
names:
ABCDEFGHIJKLMNOPQRST
UVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
!"#$%&’()*+,-./<=> ?
@[]ˆ_'{|}
5 Change between uppercase,
lowercase, and numbers/
symbols by pressing DISPLAY/
CHARA.
The case of the character at the current
cursor position changes between upper-
and lowercase and numbers/symbols with
each press.
6 Confirm the character and
move the cursor to the next
character position by pressing
the jog dial (or
¡).
For the remote, move the cursor to the next
character position by pressing
ENTER .
• Move the cursor backwards or forwards
along the display using
1 and
¡.
• Insert a new character into a name by
moving the cursor to the character
position you want and repeating steps
4–6.
TEXT MARK
A B C D E F
G H I M N O J K L
P Q R S T U V W X Y Z
1 2 3
4 5 6
7 8 9
10/0 >10
0!"#$%&’()*+,-./<=>
?@[]ˆ_'{|}
◊ÛB->?/
MONITOR
INPUT SELECTOR AUTO MANUAL
AUTO MANUAL
TRACK NO. WRITE
TIME
FINALIZE ERASE
SCROLL
5
ENTER
CURSOR
MENU/ DELETE NAME MARK
SET CLEAR
DISPLAY /CHARA
7
1 ¡
8
3
4 ¢
A B C D E F
G H I M N O J K L
P Q R S T U V W X Y Z
REC SYNCHRO
REPEAT RANDOM NAME CLIP
INPUT
SELECTER
FADER
SKIP PLAY SKIP ID
PROGRAM CHECK CLEAR
AUTO/
MANUAL
1 2 3
4 5 6
7 8 9
10/0 >10
SCROLL
TIME
Î
•
4
5
6 2,7
7 7
6
3,6
6
DIGITAL REC LEVEL ANALOG REC LEVEL
MENU/ DELETE TEXT
SYNCHRO
PUSH ENTER
R L ANALOG REC BALANCE
Legato Link Conversion CD TEXT
6 2,7
3,6
6
Using CD text
You can name a CD-R or CD-RW so that
when you load the disc into the player, the
disc name, track title, or artist name can
appear in the display. Each title can be up
to 120 characters long, including spaces.
You can store all the text (up to 2000
characters) for up to three non-finalized
discs in the recorder at one time. This is
useful when you want to edit the text
during another recording session with the
same disc.
Be careful: When you set text for a
fourth disc, the oldest text information (for
the first disc) is deleted from memory. Text
with CD-RW discs is deleted when you
erase the corresponding track.
Once you finalize a CD-R, the text
information cannot be changed. Finalized
CD-Rs containing CD text can still be
played on ordinary (non-CD text
compatible) CD players, however the CD
text will not appear in the display.
1 Make sure the disc you want to
name is loaded into the
recorder and is stopped.
For track names: Before proceeding to
step 2, you must choose the track you want
to name by turning the jog dial.
You can also name tracks during
playback.
2 Press NAME.
Press
NAME to switch between disc and
artist name:
If you are naming a track, go to
step 3.
The default is disc title. Press
7 at any
time to exit.
3 Wait two seconds after making
your selection, or press ENTER.
If the disc doesn't already have a name,
the character display is blank, with a
blinking cursor on the first character.
DISC NAME ARTIST NAME