Philips RT30A - Manual (Page 17)

The RECORD MODE SET UP menu will appear.
ALARM REC MODE - This defines the alarm recording mode
option. When an alarm occurs, the VCR will record the alarm at
the selected tape speed 6H, 18H or 30H, and then revert back to
the real-time recording speed.
3. Press the
↓ button to choose the ALARM REC MODE
option.
4. Press the
→ button to select alarm recording hours.
ALARM REC TIME - This defines the amount of time that the
alarm is recorded, 30 sec., 1 min., 3 min., 5 min., 10 min. or
T.END.
5. Press the
↓ button to choose the ALARM REC TIME option.
6. Press the
→ button to select the desired time of recording, 30
sec., 1 min., 3 min., 5 min., 10 min. or T.END (Tape end).
If you choose the T.END, alarm recording is continued
until tape end is reached.
While the alarm is in process, the buzzer will ring. If you
want to stop buzzer, press CLEAR button.
The ALARM indicator in VCR indicator panel will appear
when the alarm recording is proceeding.
1SHOT REC - This defines the interval time that one picture is
recorded, 1 sec., 3 sec., 5 sec., 15 sec., 30 sec., 60 sec. or OFF.
Notes:
If you select the '000H' option in normal recording, the
VCR will activate the '1SHOT REC' mode function. This
will record a single shot picture after each defined time
interval which is programmed in the '1SHOT REC'
menu.
If you select '1SHOT REC' OFF, the unit will record one
picture each time the external 1SHOT REC input is
activated.
7. Press the ↓ button to choose the 1SHOT REC option.
8. Press the
→ button to select the desired time of recording,
1 sec., 3 sec., 5 sec., 15 sec., 30 sec., 60 sec. or OFF.
VEXT : In case of connecting the extemal equipment (switcher or
multiplexer), you can set the switching time of the camera.
9. Press the
↓ button to select the VEXT option and then press
the
→ button to select either 1 Field, 2 Field, 5 Field,
10 Field, 30 Field, or 60 Field (these are the number of fields
recorded after one VEXT pulse).
Note:
Your update rate will be decreased with the same factor as
the number of fields selected.
SERIES REC - The Series Recording mode is convenient, when
you record with two or more VCRs. If you have two VCRs in the
Series Recording mode, the second VCR will start to record
automatically at the end of the first VCR recording.
Notes:
Before Series Recording, refer to the connection diagram
on how to connect Series Record VCRs.
Make sure a tape is in the each VCR and the safety tab is
in place.
The SERIES recording is not available when the Timer
recording is in stand-by mode.
The SERIES and REPEAT options on the REC MODE
menu are not be set to the ON mode simultaneously.
10. Press the
↓ button to choose the SERIES REC option and
press the
→ button to choose ON/OFF for each VCR.
REPEAT - This function is used to select how the recording tape
is used before starting a recording. These are:
STOP AT EOT : Tape stops when it reaches end of tape
in RECORD mode.
RE-REC EVEN IF ALARM
: Rewinds tape and enters
RECORD mode at beginning of tape even if there has
been alarm.
REWIND, STOP
: Rewinds tape and then enters STOP
mode.
STOP IF ALARM
: Rewinds tape and enters RECORD
mode at beginning of tape, if there has been an alarm
recording it enters the STOP mode at end of tape.
11. Press the
↓ button to choose the REPEAT option and press
the → button to choose the available options (see list above).
1-15
Record
(6H-960H mode)
Record
(6H, 18H, 30H
mode)
Record
(6H-960H mode)
Record
(6H, 18H, 30H
mode)
Real Time
Record
Alarm
Record
Real Time
Record
Alarm
Record
Record Start Alarm signal
is input
Alarm record
duration is ended
Alarm signal
is input
RECORD MODE SET UP
< RECORD MODE SETUP >
ALARM REC MODE A6H
ALARM REC TIME 30SEC
1SHOT REC 1SEC
VEXT OUT 1FIELD
SERIES REC OFF
REPEAT:
STOP AT EOT.
[ ↓ →] [END:MENU]