Panasonic SA-XR700 - Manual (Page 22)

22
RQT8743
Auto speaker setup using the setup microphone
Using the supplied setup microphone, you can measure such items as distance from the seating area, polarity and size
and make adjustment for connected speakers.
Keep quiet during the auto speaker setup. Conversational voice, air-conditioning noise and small sounds made
by winds may cause an error or produce an incorrect setting. Speakers output loud test signals during the auto
speaker setup. Make sure to keep little children out of the room.
• Mute the TV volume before starting the auto speaker setup.
• When the subwoofer is connected, make sure it is turned on. (There are subwoofer models that turn off automatically.)
Set the subwoofer volume to the normal listening level.
• Select “Yes ” in “Making bi-wire setting” (á page 20) when you connect the unit to bi-wire speakers.
• The setup microphone is sensitive to heat. Keep it away from direct sunlight and avoid placing it on top of the unit.
• These settings remain effective after the unit goes off.
• The setup microphone jack is for use with the setup microphone only. Do not connect other microphones.
• The volume may reach an extremely high level when you repeat the auto speaker setup.
When the auto speaker setup is finished, check the volume before starting playback.
To cancel the setup
halfway
Press [TEST, –AUTO].
1
To turn the unit on
Press
• The standby indicator “^” goes off when you turn the unit on.
2 To select “SPEAKERS A”
Press (on the unit) to switch “ ” on.
3 Connect the setup microphone.
4
5
Place the setup microphone.
• Place the setup microphone on a flat surface to stabilize it.
Examples: a level bench sharing the height with
the seating area, a top section of a sofa etc.
• Set the microphone at seated ear height.
• Use a tripod (for camera and other products) for best results.
To start the setup
Press and hold (on the remote
control) for 2 seconds.
• The “AUTO SPEAKER SETUP” indicator flashes.
• When all auto settings are made, “ COMPLETE ” appears and the “AUTO SPEAKER SETUP” indicator lights on.
• The auto speaker setup takes about 3 minutes to finish in the case of a 5.1-channel system.
• The unit cancels the auto speaker setup halfway through when you give a different
operational instruction before the setup finishes.
• You can perform other operations after “ COMPLETE ” is displayed. The unit keeps the
settings even if you move straight on to another operation.
6 To finish the setup
Press (on the remote control).
• The unit turns off and on in quick succession for completing the setup.
• Unplug the setup microphone when the setup is finished.
Such factors as speaker types, room conditions and speaker placement may cause the unit to set speaker size, lowpass filter frequency and other
items differently for the same type of speakers or produce settings that differ from the actual characteristics of respective speakers.
When sound from speakers seems odd, check the following settings. When you find undesirable settings, correct them manually.
• See “Setting speakers and their sizes”, “Setting distances” and “Setting the lowpass filter” (á page 33).
“ ”
-MENU/-SETUP ENTER
INPUT SELECTOR VOLUME
BI-AMP SURROUND
SURROUND SPEAKERS
AUTO DETECTOR
TUNE AUX
ADVANCED DUAL AMP
AUTO SPEAKER SETUP
SETUP MIC
HDMI
RETURN
SURROUND SPEAKERS ENTER - MENU/ - SETUP
AUTO DETECTOR RETURN TUNE
AUX S VIDEO VIDEO L - AUDIO - R SETUP MIC
“AUTO SPEAKER SETUP”
A
SPEAKERS
ONE
TOUCH PLAY
DI
RE
CT
NA
VI
GA
TO
R
TO
P
M EN
U
FU
NC
TIO
N
S
0
RECEIVER
AV
SYSTEM
TV
RECORDER
DVD
BD/DVD
PLAYER
ANALOG 6CH
VCR CD
TUNER
BAND
CH
VOLUME
SKIP SLOW/SEARCH
STOP PAUSE PLAY
DRIVE SELECT MANUAL SKIP
ENTER
SUB MENU RETURN
OFF
SUBWOOFER TV
LEVEL EFFECT VOL
NEO : 6
SFC
MUSIC MOVIE MUTING
TV/AV
DIMMER
-/- - DISC
DIRECT
TUNING
TEST
AUTO
8
A
SPEAKERS
A A
SPEAKERS
AUX
AUTO SPEAKER SETUP
SETUP MIC
HDMI
AUX S VIDEO VIDEO L - AUDIO - R SETUP MIC
Tripod
TEST
AUTO
TEST
AUTO
Note
Auto speaker set
up using the setup microphone
ENGLISH
SA_XR700_EG_GN_ (RQT8743_B)ver.3.fm 22 ページ ２００６年８月３１日 木曜日 午前９時７分