Philips FW-C150 - Manual (Page 17)

3139 115 20541 (ENG)
17 TUNER
DIGITAL SOUND CONTROL
STANDBY-ON
PROGRAM CLOCK •TIMER
MASTER
VOLUME
MINI HIFI SYSTEM
C D 1 • 2 • 3 TAPE 1 • 2
TAPE CD AUX
PRESET ▲ ▲ TUNING ▲ ▲ ▲ ▲
STOP• CLEAR SEARCH PLAY• PAUSE PREV NEXT
3 CD ROTARY CHANGER SYSTEM •
CD REWRITABLE COMPATIBLE •
CD SYNCHRO RECORDING •
VIDEO
O P TI M AL JA ZZ
R O CK
TE C H N O
DSC DYNAMIC BASS BOOST
FM•AM
TUNER
DEMO STOP
Note:
– For 'PLUG & PLAY' feature, please refer
to page 12.
Tuning to radio stations
1 Press TUNER (FM•AM) to select
TUNER mode.
™ “TUNER” will be displayed.
A few seconds later, the current
radio frequency will be displayed.
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press à or á for more than one
second, then release.
™ The display will show “SEARCH”
until a radio station with sufficient
signal strength is found.
• Repeat this procedure until the
desired station is reached.
• To tune to a weak station, briefly
press à or á repeatedly until the
display shows the desired frequency
and/or when the best reception has
been obtained.
Storing Preset Stations
You can store up to 40 radio stations in
the memory. When a preset radio
station is selected, the preset number
appears next to the frequency on the
display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROGRAM for more than
one second.
™ The PROG flag starts flashing and
“ AUTO” will be displayed.
™ The system will search for every
available station in the FM
waveband first, then search the
AM waveband.
™ All available stations will be stored
automatically. The frequency and
preset number will be displayed
briefly.
™ The system will stop searching
when all the available radio
stations are stored or when the
memory for 40 preset radio
stations is used.
™ The system will remain tuned to
the last stored preset radio
station.
Notes:
– You can cancel the automatic
programming by pressing PROGRAM or
Ç (on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10
before starting automatic programming,
only the preset numbers 10 to 40 will
be programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press PROGRAM for less than one
second.
™ The PROG flag starts flashing.
™ The next available preset number
will be displayed for selection.
4 Press à or á to tune to the
desired frequency.
• If you wish to store the radio station
to another preset number, press 4
or 3 to select the desired preset
number.
5 Press PROGRAM again.
™ The PROG flag disappears and
the radio station will be stored.
• Repeat steps 3 – 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show "
FULL”. If
you want to change an existing preset
number, repeat steps 3 – 5.
– You can cancel manual programming
by pressing Ç (on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
• Press 4 or 3 to select the desired
preset number.
™ The preset number, radio
frequency, and waveband appear
on the display.
pg 01-28/C150/37-En 12/6/00, 2:18 PM 17