Pioneer VSX-72TXV - Manual (Page 71)

Controlling the rest of your system 11
71
En
5 Use / to select a command in the sequence then
press ENTER.
If this is the first command in the sequence, select 1ST
CODE. Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER.
6 If necessary, press the input source button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
7 Select the button for the command you want to
input.
The following remote control commands can be
selected:
• You don't need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components , you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
• program the power to switch on if it’s the source
component selected in step 3;
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
These take priority in multi operations (not shutdown).
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use / to select EDITEXIT
from the menu and press ENTER.
You will return to the remote control SETUP menu. Select
* EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press SOURCE.
The command sequence you programmed will run, then
all Pioneer components will switch off
1
, followed by this
receiver.
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see Setting the remote to control other
components
on page 68 for more on this). Use the input
source buttons to select the component.
• The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CONT
button. If you have two TVs, assign the main TV to the
TV CONT button.
SLEEP
+10
SR+
ANALOG
ATT
DISC
VIDEO
SEL
DIMMER
CLASS D.ACCESS
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
ENTER
TV CONTROL
DVD SAT VIDEO 1 TV CONT
DVR1
TUNE
TUNE
ST ST
i Pod TUNER RECEIVER
ENTER
AV PARAMETER
TOP MENU ì
DTV MENU
CH LEVEL
MENU
T.EDIT
BAND GUIDE
RETURN SETUP
CATEGORY
CD
DVR2 CD-R
TV VIDEO 2
XM RADIO ROOM2/3
TV CONTROL
VOL
STATUS SIGNAL SEL SBch STEREO
MEMORY
TV CH INPUT
SELECT
MPX
AUDIO SUBTITLE
DTV INFO MUTE REC
TV VOL
REC STOP
HDD
CH CH
DVD
DISP
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
Button(s) Function Components
TV Press to switch the component
assigned to the TV CONT
button on or off. Cable TV/Satellite
TV/TV/DTV
INPUT
SELECT Switches the TV input. (Not
possible with all models.) Cable TV/Satellite
TV/TV/DTV
SHIFT
STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL SBch STEREO
ADV. SURR STANDARD
PHASE
THX
RECEIVER
RECEIVER SOURCE
SYSTEM OFF
INPUT
SELECT
DVD SAT VIDEO 1 TV CONT
CD TV VIDEO 2
SHIFT
STATUS
MCACC S.DIRECT
MULTI OPE
SIGNAL SEL SBch STEREO
ADV. SURR STANDARD
PHASE
THX
RECEIVER