beautypg.com

Pentek NSF US-1000 User Manual

Specifications, Parts included, Precautions

background image

Technical Support: 800.861.8758 (M-F 7:30 a.m. - 5:00 p.m. CST)

MTBE Filtration System

Installation and Operating Instructions

Model US-1000

Specifications

Temperature Range:

40–100°F (4.4–37.8°C)

Pressure Range:

30–125 psi (2.1–8.62 bar)

Service Flow Rate @ 60 psi (4.1 bar): 0.6 gpm (2.3 L/min)
Rated Service Life:

1,000 gallons (3,785L)

Dimensions:

9.18 in. x 4.70 in. x 12.72 in.

(233 mm x 119 mm x 323 mm)

Weight:

6 lbs. (2.7 kg)

Parts Included

• Filter system with filter cartridges – P-250A Cartridge Set
• Installation hardware

(mounting screws, T-Adapter, quick-connect elbows)

• Housing wrench
• Lead-free drinking water faucet
• 1/4" plastic tubing

Precautions

WARNING:

Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts.

CAUTION:

Filter must be protected against freezing, which can

cause cracking of the filter and water leakage.

CAUTION:

The rubber O-ring provides the water-tight seal between

the cap and the bottom of the housing. It is important that the O-ring

be properly seated in the groove below the threads of the housing or a

water leak could occur.

CAUTION:

Because of the product’s limited service life and to

prevent costly repairs or possible water damage, we strongly

recommend that the bottom of all plastic housings be replaced every

ten years. If the bottom of your housing has been in use for longer

than this period, it should be replaced immediately. Date the bottom of

any new or replacement housing to indicate the next recommended

replacement date.

Tools and Materials

Required

• Safety glasses

• Hand or electric drill

(cordless recommended)

• 1/4" drill bit

• File

• Phillips head screwdriver

• Adjustable wrench or 7/16”

open-end wrench

• Tube cutters or utility knife

If sink does not have hole for

separate faucet:

• Center punch

• 3/4" drill bit or hole saw

NOTE:
• For cold water use only.
• Make certain that installation complies with all state and local

laws and regulations.

• The contaminants or other substances removed or reduced by

the selected cartridge are not necessarily in your water. Ask your

local water municipality for a copy of their water analysis, or have

your water tested by a reputable water testing lab.

• After prolonged periods of non-use (such as during a vacation) it

is recommended that the system be flushed thoroughly. Let water

run for 5–6 minutes before using.

• The filter cartridges used with this system have a limited service

life. Changes in taste, odor, and/or flow of the water being filtered

indicate that the cartridge should be replaced.

About Your PENTEK MTBE Filtration

System

Thank you for purchasing a PENTEK MTBE Filtration System. With

only minimal maintenance, your new system will provide you with

safer, better-tasting water for years to come. The filter cartridges

should be changed after every 500 gallons of use or once every six

months, whichever comes first. Filter life will vary depending on usage

and water conditions. Changes in taste, odor, and/or flow of the water

being filtered indicate that the filter cartridges should be replaced.

US-1000 MTBE Filtration System

The US-1000 MTBE Filtration System uses two carbon filter cartridges

specially formulated to provide safer, cleaner, and better-tasting

water. The US-1000 filtration system is NSF certified to reduce MTBE,

chlorine taste & odor, asbestos reduction and cyst removal, lead,

mercury and VOC’s in drinking water (see performance data on p. 7 for

specific claims).
Lead is tasteless and colorless, and may enter your water supply

through lead pipes, lead solder, and brass fittings and faucets. The

US-1000 system has been Tested and Certified by NSF International to

reduce lead below the USEPA Action Level.

The Model US-1000 is Tested and Certified by NSF

International against NSF/ANSI Standard 42 for the reduction

of Taste and Odor, Chlorine, and Particulate Class I. Standard

53 for the reduction of MTBE, Lead, Mercury, VOC, Cyst,

Asbestos, and Turbidity.

146597 JA05