Pioneer VSX-1017AV-K - Manual (Page 59)

Controlling the rest of your system 12
59
En
8 Repeat steps 5–7 to program a sequence of up to
five commands.
9 When you’re finished, use / to select EDITEXIT
from the menu and press ENTER.
You will return to the remote control
SETUP menu. Select
* EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Using System off
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press  SOURCE.
The command sequence you programmed will run, then
all Pioneer components will switch off
1
, followed by this
receiver.
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see
Setting the remote to control other
components on page 57 for more on this). Use the input
source buttons to select the component.
• The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL button.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
SHIFT
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH CH
DVD
RECEIVER
STEREO/
F.S.SURR
PHOTO
THX STANDARD
AUTO SURR SIGNAL SEL
ADV.SURR
EFFECT/CH SEL LEVEL
ACOUSTIC EQ
RECEIVER SOURCE
SYSTEM OFF
INPUT SELECT
TV DVR 1 TV CTRL DVD
DVR 2
SHIFT
AUDIO
DISP
SUBTITLE
MULTI OPE
HDD
CH CH
DVD
RECEIVER
STEREO/
F.S.SURR
PHOTO
THX STANDARD
AUTO SURR SIGNAL SEL
ADV.SURR
EFFECT/CH SEL LEVEL
ACOUSTIC EQ
Button(s) Function Components
TV  Press to switch the component
assigned to the
TV CTRL
button on or off.
Cable TV/
Satellite TV/TV
INPUT
SELECT Switches the TV input. (Not
possible with all models.) TV
TV CH +/– Selects channels. Cable TV/
Satellite TV/TV
TV VOL +/– Adjust the TV volume. Cable TV/
Satellite TV/TV
SOURCE  Switches the TV or CATV
between standby and on. Cable TV/
Satellite TV/TV
 Use to choose the ‘A’
commands on a Satellite TV
menu. Satellite TV
 Use to choose the RED/B
commands on a Satellite TV/TV
menu. Satellite TV/TV
 Use to choose the CYAN/E
commands on a Satellite TV/TV
menu. Satellite TV/TV
 Use to choose the GREEN/C
commands on a Satellite TV/TV
menu. Satellite TV/TV
 Use to choose the YELLOW/D
commands on a Satellite TV/TV
menu. Satellite TV/TV
AUDIO / DISP Use to switch audio tracks. Satellite TV/TV
SUBTITLE Use to return to the previously
selected channel. Cable TV/
Satellite TV/TV
GUIDE
Use as the GUIDE button for
navigating.
Cable TV/
Satellite TV/TV
RETURN Use to select RETURN or EXIT. Satellite TV/TV
Number
buttons Use to select a specific TV
channel. Cable TV/
Satellite TV/TV
+10 button Use to add a decimal point
when selecting a TV channel. Satellite TV/TV
ENTER/
DISC Use to enter a channel. Cable TV/
Satellite TV/TV
MENU Select the menu screen. Cable TV/
Satellite TV/TV
///
&
ENTER
Select, adjust and navigate
items on the menu screen. Cable TV/
Satellite TV/TV
TOP MENU Switches TEXT ON/OFF for TVs. TV
VSX-1017_HY.book Page 59 Tuesday, March 6, 2007 3:53 PM