Phoenix Gold pm700 - Manual (Page 5)

pm700
• 225W per channel into 8 ohms
350W per channel into 4 ohms
700W mono into 8 ohms
• XLR and 1/4” TRS input connectors
• Accepts balanced or unbalanced lines
• Multi-way Binding Post output connectors
• Independent 11 detent level controls for
CH1 and CH2
• External Level Control Defeat Switch
• Dual Mono mode for operating both channels
with
a single mono input
• Bridged Mono mode for combining the power of
both channels into a single higher powered chan-
nel
• Input sensitivity set at 1.5V RMS from factory.
Internally configurable to 0.775V RMS
• Internally configurable input polarity
• Internal connection points for add-on accessories
• Power ON Sequencer
• Class H dual-rail power supply
• Independent CH1 / CH2 Speaker relays will
instantaneously disconnect if one of the following
fault conditions is detected:
D.C. Offset
Over Temperature
Short Circuit
• Additional protection circuitry includes:
Clipping Eliminator
AC Line Fuse
• Power Connected / Standby indicator
• 7 LED display per channel, including Power
Ready
and Clip / Protect indicators
• 2-speed Fan cooled
• 70-volt / 100-volt transformer option
• CE 1997 approved
2
Power Output:: (20Hz to 20kHz, with no
more than 0.1% THD)
225 watts per channel
into 8 ohms
350 watts per channel
into 4 ohms
Bridged-mono:
700 watts into 8 ohms
at 1kHz, with no more
than 0.1% THD
Dynamic Headroom: >2.0dB
F requency Response:
20Hz to 20kHz (±0.75
dB)
Channel Separation:
>65dB @ 1kHz
Damping Factor: <400
Input Impedance: 25 Kohms unbalanced
50 Kohms balanced
Sensitivity: Low: 1.5 V RMS for
rated power into 4
ohms 160mV
RMS for
1W into
4 ohms
High: 0.775V
RMS for-
rated power into 4
ohms 83mV
RMS for 1W
into 4 ohms;
Gain: High: 33.8dB (±0.5dB)
Low: 27.8dB (±0.5dB)
Input Overload: +18dB
THD: <0.1%
IM Distortion: <0.1%
Signal-to-Noise Ratio:
>100 dB, A-weighted,
ref. to rated power into
4 ohms
Slew Rate: 40V / µS
(Bandwidth limited)
CMRR: >80dB @ 1kHz
Power Consumption:
55W at idle; 500W with
musical program;
1000W at full power
into 8 ohms (continu-
ous); 1550W at full
power into 4 ohms
(continuous)
Power Requirements:
120VAC / 60Hz (USA
and Canada) Other
voltages as required
for export
Fusing: 10 amp slo-blo
(120V / 60Hz) 7 amp
slo-blo (230V / 50Hz)
Sequence Receive Terminal:
+7V to +15V DC
50mA min. current
requirement
Display: 7 LED indicators per
channel 1 green
READY, 5 yellow SIG-
NAL, 1 red CLIP /
PROTECT
Size (H x W x D): 3.50” (2U) x 19” x
13.25” 89
mm x 483 mm
x 337 mm
Net Weight: 30 lbs. (13.6 kgs)
Shipping Weight: 36 lbs. (16.3 kgs)
Due to on-going product development,
features, specifications, and availability are
subject to change without notice.
3
BACK