PYLE Audio PQA3100 - Manual (Page 2)

Designed and engineered in U.S.A Designed and engineered in U.S.A
PQA5100
2550+2550wrms
1200+1200w
600+600w
2400+2400w
>85dB >85dB >90dB
>70dB
>250 >250 >250
30v/μs
<140W <300W <300W
482x314x88mm
8kg 9.5kg 11.5kg
。
。
。
。
。
。
Installation guidelines
DO NOT use these amplifiers in damp or high humidity environments.
Do not use outdoors or anywhere where liquids could fall or splash onto the amplifier.
Ensure the amp is adequately ventilated, with free airflow to the front and rear panels.
Keep away from other heat sources. If the amps are mounted in a rack with other amps,
ensure there is adequate cool air flow front and rear. Note that air is drawn in through
the back panel, and exhausted through the front panel.
NEVER cover the amplifiers, as they may overheat.
PQA power amplifiers are designed to fit standard 19 racks, with a 2U height
and 17 depth. We recommend the use of rear rack supports, especially if the rack is to
be mobile. Use shake proof washers or thread lock adhesive to prevent mounting bolts
becoming loose in transit.
Ensure that the AC power supply is correct for your amplifier. The required AC supply
is stated on the rear panel next to the AC power input.
Ensure that you use the correct type of mains lead for your equipment and country.
This must be free from damage and easily accessible during use.
1550+1550wrms
760+760w
380+380w
1520+1520w 1050+1050wrms
460+460w
230+230w
920+920w
Model PQA4100 PQA3100 PQA2100
2050+2050wrms
1000+1000w
500+500w
2000+2000w
10Hz-50KHz -1.5dB
21dB/9V
20K OHMS
>90dB
>70dB >70dB >70dB
>250
30v/μs 30v/μs 30v/μs
Variable Speed Fan
<300W
AC 115V-230V/50-60Hz
10.5kg
2 O H M S
THD
PQA PQA
www.pyleaudio.com www.pyleaudio.com
h
Short circuit,C urrent limiter,T ermal cut off,Slow Start,
Limiter,AC line fuse, DC fault,Power up/down transients
OVERVIEW
It is well- known the PQA series professional amplifier is designed by the
specialist who has full experience and new model equipment. To raise
reliability of the amplifier, PQA series professional amplifier has been
installed with short distance cooling unit,
high- speeding and consistency to increase the life of the power parts. They
all have adopted mature and reliable circuit with SMT technology.
The conventional amplifier applies tunnel- model cooling system, this kind
of system has long distance for heat dissipation, the hot air is distributed
with difficulty, and theradiator is very hot at the top, but too cool at the
bottom, the temperature difference goes between 2 0℃- 4 0℃, those system
produces temperature difference easily in the power parts, the electric
current is high in hot parts, which results in its damage and reduces the
using- life and reliability.
PQA series amplifiers has full-protection, including:
Soft start function to prevent wave shock at power- on.
Delay function for prevent shock at switch power on.
DC protection.
Over- electric current protection.
Cut- wave protection.
Over heat protection.
ATTENTION
Never put any parts on the top of the amplifier.
Using fixed power socket that must be has enough capacity to prove power.
Never switch the power on and off continuously at the same time.
Donruction in the air vent of front panel.
Input stereo level can be adjust by own gain mixer, in bridge- model connection,
the adjustment will adjust by CHA channel mixer.
The output connector have 3 kind model, tie- model, phone model and professional
speakon connector for connecting.
When using stereo, bridge, mono function, the connect model must be same than
model switch selected.
When output high- power signal continuously, the amplifier should be has speed-
up in the cooling fan, it may be have low noise produce in this equipment, it is
normally.
The general gain of the amplifier can be adjust by gain knob, the input level
have 0 . 7 7 V, 1 . 4 V, full- power out and fixed 2 6 dB gain 3 band should be selected.
Donr vent of rear panel.
When clear- up the cover of the equipment, you must be power off and loose the
power Plug using dry- cloth to clear, never using and solvent that have corrosive
to clear.
If have problem happened, power down immediately, and contact with dealer.