beautypg.com

Planet Technology FSD-503 User Manual

Package contents, Switch front panel, Installing the switch

background image

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Check the contents of your package for following parts:

● Fast Ethernet Switch x 1

● User's manual x 1

● Power adapter x 1

● Rubber feet x 4

If any of these are missing or damaged, please contact your
dealer immediately, if possible, retain the carton including
the original packing material, and use them against to
repack the product in case there is a need to return it to us
for repair.

3. Switch Front Panel

Figure 1-1 & 1-2 & 1-3 shows a front panel of FSD-503 /
FSD-803 / FSD-1603.

Figure 1-1 FSD-503 front panel

Figure 1-2 FSD-803 front panel

Figure 1-3 FSD-1603 front panel

6. Installing the Switch

This part describes how to install your Fast Ethernet Switch
and make connections to it. Please read the following topics
and perform the procedures in the order being presented.

Note

This Switch does not need software
configuration.

Desktop Installation

To install the Switch on desktop, simply follow the next
steps:

Step 1: Attach the rubber feet to the recessed areas on

the bottom of the Switch.

Step 2: Place the Switch on desktop near an AC power

source.

Step 3: Keep enough ventilation space between the Switch

and the surrounding objects.

Note

When choosing a location, please keep in
mind the environmental restrictions discussed
in Chapter 7. Product Specifications.

5. Switch Rear Panel

Figure 1-4 & 1-5 & 1-6 shows a rear panel of FSD-503 /
FSD-803 / FSD-1603.

Figure 1-4 FSD-503 rear panel

Figure 1-5 FSD-803 rear pane

Figure 1-6 FSD-1603 rear panel

2. Product Features

● Comply with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-

TX Ethernet standards

● 5/8/16-Port 10/100Mbps Fast Ethernet ports

● Features Store-and-Forward mode with wire-speed

filtering and forwarding rates

● Hardware based 10/100Mbps, half / full duplex, flow

control and auto-negotiation

● IEEE 802.3x flow control for full duplex operation and

Backpressure for half duplex operation

● Integrated address look-up engine, support 1/2/8K abso-

lute MAC addresses

● 384K / 512K bits packet buffer memory (FSD-503/803)

● 4Mbit on-chip frame buffer (FSD-1603)

● Automatic address learning and address aging

● Supports Auto MDI/MDI-X function

● Support CSMA/CD protocol

● External power adapter 12V 0.5A (FSD-503/803)

● External power adapter 12V 1A (FSD-1603)

● FCC, CE class A compliant

4. LED Indicators

FSD-503/FSD-803

LED

Color

Function

PWR

Green

Lit: Power on.

LNK/ACT

Green

Lit: indicate the link through that port

is successfully established.

Blink: indicate that the Switch is

actively sending or receiving
data over that port.

FSD-1603

LED

Color

Function

PWR

Green

Lit: Power on.

10/100

Green

Lit: indicate that the port is operating

at 100Mbps.

Off: indicate that the port is operating

at 10Mbps.

Blink: indicate that the Switch is

actively sending or receiving
data over that port.

Power

Notice

1. The device is a power-required device, it

means, it will not work till it is powered. If
your networks should active all the time,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will
prevent you from network data loss or
network downtime.

2. In some area, installing a surge

suppression device may also help to protect
your Switch from being damaged by
unregulated surge or current to the Switch
or the power adapter.

Step 4: Connect your Switch to network devices.

A. Connect one end of a standard network cable

to the 10/100 RJ-45 ports on the Back of the
Switch.

B. Connect the other end of the cable to the

network devices such as printer servers,
workstations or routers…etc.

Step 5: Supply power to the Switch.

A. Connect one end of the power cable to the

Switch.

B. Connect the 12V DC power adapter to a

standard wall outlet.

When the Switch receives power, the Power LED should
remain solid Green.