Philips DVD-930 - Manual (Page 9)

ENGLISH
9
CONNECTING THE POWER SUPPLY
• Plug the female end of the power cable supplied into the
Power connector (1) on the rear of the player.
• Plug the male end of the cord into an AC outlet.
NOTE
– The player will automatically adjust to the local mains voltage.
– When the player is in the “OFF” position, it is stil consuming
some power. If you wish to disconnect your player completely
from the mains, withdraw the plug from the AC Outlet.
CAUTION
ONLY A QUALIFIED SERVICE PERSON SHOULD REMOVE
THE COVER OR ATTEMPT TO SERVICE THIS DEVICE.
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE OR
OTHER UNSAFE CONDITIONS.
INFRA RED REMOTE CONTROL
LOADING THE BATTERIES
• Open the battery compartment cover.
• Insert 3 'AA' (R6 or SUM3) batteries as indicated inside the
battery compartment.
• Close the cover.
CAUTION
DO NOT MIX OLD AND NEW BATTERIES. AND NEVER MIX
DIFFERENT TYPES OF BATTERIES (STANDARD, ALKALINE
AND SO ON).
STANDARD CONNECTIONS
PROGRAMMING THE UNIVERSAL REMOTE CONTROL
The remote control of the DVD-Video player can be
programmed to control your Television, Amplifier or Receiver.
For the control of these products the following buttons on the
remote control are available:
• Amplifier - Volume Up/Down and Audio Mute.
• Receiver - Volume Up/Down and Audio Mute.
• Television - Volume Up, Volume Down, Channel Up/Down
and TV Mute.
In order to change the remote control to control your brand of
Television, Amplifier or Reciever follow the next steps.
1 Select either your brand of Television, Amplifier or Receiver
from the next table. Mark the first 3 digit code number
behind the brand name.
2 Press ENTER en RETURN simultaneously until the Jog/Pause
button lights up.
NOTE
– Note that your remote control is now disabled for all
functions.
3 Enter the digits of the selected 3 digit code number. Every
time you enter a digit, the Jog/Pause button will blink shortly.
When entering the last (3-rd) digit, the Jog/Pause button will
blink twice and then switches off to confirm that the
programming sequence was correctly executed.
NOTE
– In case you press a wrong key or an incorrect number, the
Jog/Pause button will switch off and flashes once. The remote
control has not been re-programmed. Repeat step 1,2 and 3.
4 The remote control is now programmed to control your
Television or Amplifier or Receiver. If it does not react
properly on the mentioned buttons, select the next 3 digit
code number behind the your brand of Television, Amplifier
or Receiver and repeat step 2 and 3.
AMPLIFIERS CODE
Aiwa
431
Grundig 420, 432
Kenwood 428, 447
Marantz 420
Philips 420, 445
Pioneer
401
Sony 415
Technics 423, 434
Yamaha 427
RECEIVERS CODE
Aiwa 536, 546, 573, 581,
586, 606, 617, 636,
647, 649
Denon 502, 704
Grundig 557, 561, 580
Harman/
Kardon
531
JVC 521, 630, 645, 658
Kenwood 510, 523, 589, 590
Luxman
660, 705
Marantz 538, 557, 568
Onkyo 528, 535, 539
Philips 557, 663, 677
Pioneer 582, 645
Sansui 665, 689
Sony 545, 549
Technics 564, 588
Yamaha 526, 551, 691
TELEVISION CODE
Bang &
Olufsen
057,058
Grundig 048, 115, 119, 124, 256,
267, 271
Hitachi 026, 029, 033, 034, 064,
071, 074, 079, 095, 120,
121,134, 137, 139, 160,
173, 196, 230, 269, 273,
276
JVC 029, 039, 047, 092, 098,
114, 116, 207
Panasonic 095, 130, 131, 138, 149,
192, 204, 273
Philips 000, 010, 011, 030, 033,
058, 117, 181, 209, 271
Radiola 010, 030, 181
Saba 052, 058, 074, 095, 120,
121, 124, 130, 165, 170,
187, 194, 273
Samsung 000, 007, 030, 032, 059,
134, 155, 166, 184, 206,
253, 257
SBR 010, 011, 030, 033, 117
Schneider 011, 030, 135, 148, 172,
181, 188, 197, 207, 221,
268
Sony 001, 008, 009, 029, 075,
263
Telefunken 006, 051, 056, 068, 074,
130, 151, 154, 173, 187,
194, 251, 260
Thomson 074, 120, 121, 124, 165,
170, 186, 194, 196, 223
Toshiba 028, 029, 048, 147, 262,
270
1/DVD-930/935-ENGLISH 10-08-1999 09:55 Pagina 9