Philips 14PV365/07 - Manual (Page 17)

EN 14
General information
Use a TIMER programming to automatically start
and stop a recording at a later time or date. The
TV-Video Combi will switch to the right pro-
gramme number and begin recording at the cor-
rect time. With this
TV-Video Combi , you can pre-
programme up to eight recordings within a peri-
od of one year. To make a programmed record-
ing, your
TV-Video Combi needs to know:
*the date you want to make the recording
*the programme number of the TV channel
*the start and stop time of the recording
*VPS or PDC on or off
This information is saved in a TIMER block.
Programming a recording with
'VIDEO Plus
+ system ® '
Thanks to this simplifed programming system,
you no longer need to tediously enter the date,
programme number, start and end time. All the
information needed for programming is con-
tained in the PlusCode number. You can find this
PlusCode number in most TV listing magazines
written next to the concerned programme.
1. 1. Press on the remote control.
2. 2. Enter the entire PlusCode number. This num-
ber is up to 9 digits long and can be found
next to the start time of the TV programme in
your TV listing magazine. [e.g. 1-234-5 or 1
234 5]
3. 3.Enter the entire PlusCode number. This is up
to 9 digits long and can be found next to the
start time of the TV programme in your TV
listing magazine. [e.g:1-234-5 or 1 234 5]
If you make a mistake, you can clear your
input with
.
4. 4.Press .
5. 5.Select ONCE, DAILY, or WEEKLY recording
with . Then press . B 1 L C K B
SV/V+
CLEAR
SV/V+
7. Programming a recording (TIMER)
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC'
(Programme Delivery Control) are used to con-
trol the start and duration of TV channel record-
ings. If a TV programme starts earlier or ends
later than scheduled, the TV-Video Combi will
turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same as
the start time. But if your TV guide shows a
VPS or PDC time which is different from the
programme’s scheduled start time, e.g. 20.10
(VPS/PDC 20.14), you must enter the VPS/PDC
time exact to the minute. If you want a start time
different from the VPS/PDC time, you must
switch VPS/PDC off.
PlusCode
No. :1 2 3 4 5
SET=VIDEO PLUS+
CORRECT=CLEAR
END=EXIT
PlusCode
→ONCE
DAILY
WEEKLY
SELECT K L CHOOSE B
END=EXIT
Selecting once/daily/weekly recordings
Using
, select from the following
options:
'ONCE':
Recording once
'DAILY': Repeated daily recordings (Monday
to Friday)
'WEEKLY.': Repeated weekly recordings (every
week on the same day)
L C K B
Prog No changes to ' - - '
* The entered PlusCode is incorrect.
Correct your input or end with
.
The following message appears on the
screen:'ERROR'
* The entered PlusCode is incorrect. Correct
your instructions or end with
.
* Check the time/date (see chapter 'Installing
your TV-Video Combi', section 'Setting the
clock').
* A daily recording was entered for the wrong
day. Daily programming can only be used for
recordings to be made from Monday to Friday.
The following message appears on the
screen:’TIMER NOT COMPLETED’
* The channel is wrong.
STATUS/EXIT
STATUS/EXIT
PAL I(EN).qx3 02.4.2 6:42 PM Page 14