Pacific Digital AVR 635 - Manual (Page 32)

32 SYSTEM CONFIGURATION
System Configuration
In addition to the controls for selecting channels
and the test tone operation, the settings on this
menu also allow you to reset the level settings to
either the factory default of 0dB or to re-establish
the settings that were entered by running
EzSet/EQ.
To reset all channel levels to 0dB press ⁄ / ¤
Navigation Button E so that the cursor is
pointing to the LEVEL RESET line and then
press the ⁄ / ¤ Navigation Button E once
so O N appears in highlighted video.
To return to the settings established by EzSet/EQ,
even if you have made manual changes to the
output trims using the steps shown above, press
⁄ / ¤ Navigation Button E so that the cur-
sor is pointing to the EZSET SETTINGS
line and then press the ⁄ / ¤ Navigation
Button E once so ON appears in highlighted
video. Remember that after turning the EzSet/EQ
settings back on you must turn return to this
menu line and change the setting to OFF if you
wish to make any manual trim adjustments.
The final setting in this menu enables you to have
the output levels remain the same for all inputs
or to be adjusted differently for each (or any)
input. While most listeners prefer to keep the
same output levels for all sources, you may wish
to raise or lower some channels, particularly the
subwoofer output for a specific source such as a
CD that is primarily used for music playback.
To enter individual settings for a specific channel,
first make sure that you have either run EzSet/EQ
and/or made any desired manual trim adjust-
ments to set a baseline for all channels. After that
is done, press the OSD Button
L to exit the
menu system and then select the input for which
you wish to enter different level settings by using
either the Input Source Selectors % on the
front panel or the buttons on the remote that are
used to select an input source
467ç∂. Next, return to the
CHANNEL OUTPUT submenu using the
steps outlined above.
At the CHANNEL OUTPUT menu press
⁄ / ¤ Navigation Button E until the cursor
is pointing to the LEVEL TRIM line and then
press the ⁄ / ¤ Navigation Button E once
so that INDEPENDENT appears in high-
lighted video. When this setting is active you may
change the channel output levels for any input
without changing the settings previously estab-
lished for another.
When all changes to the Channel Output levels
and the associated level trim settings have been
made press the
⁄ / ¤ Navigation Button E
until the cursor is on the BACK T O MANUAL
SETUP menu and then pressing the Set
Button F so that you may make any other
adjustments to the system parameters. If the
changes just made complete the manual adjust-
ments needed, press the OSD Button
L to
exit the menu system and resume normal system
operation.
Additional Input Adjustments
After one input has been adjusted for Surround
mode, digital input (if any), speaker type, and
output levels, go back to the
IN/OUT
SETUP line on the MASTER MENU (Figure
1) and enter the settings for each input that you
will use. In most cases, only the digital input and
surround mode will be different from one input to
the next, while the speaker type, crossover fre-
quency, Night mode and output level settings will
usually be the same and may be quickly entered
by entering the same data used for the original
input.
Once the settings outlined on the previous pages
have been made, the AVR is ready for operation.
While there are some additional settings to be
made, these are best done after you have had an
opportunity to listen to a variety of sources and
different kinds of program material. These
advanced settings are described on pages 41 to
42 of this manual. In addition, any of the settings
made in the initial configuration of the unit may
be changed at any time. As you add new or dif-
ferent sources or speakers, or if you wish to
change a setting to better reflect your listening
taste, simply follow the instructions for changing
the settings for that parameter as shown in this
section.
Note that any settings changed at any time, also
when the discrete buttons are used only, will be
stored in memory in the AVR, also if it´s turned off
completely, unless it will be reset (see page 56).
Having completed the setup and configuration
process for your AVR, you are about to experience
the finest in music and home-theater listening.
Enjoy!