Pioneer DJM-700-S - Manual (Page 25)

TROUBLESHOOTING
25
En
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check
the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in
use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then
on again.
Symptom Possible Cause Remedy
No power • The power cord has not been connected. • Connect to power outlet.
No sound, or sound volume is
too low. • Input selector is set incorrectly.
• Connection cables are connected incorrectly, or
connections are loose.
• Jacks or plugs are dirty.
• The rear panel master output attenuator switch
( MASTER ATT ) is set to –6 dB, etc.
• Set input selector to playback component.
• Connect correctly.
• Clean soiled jacks/plugs before connecting.
• Adjust rear panel master attenuator switch
( MASTER ATT ).
No digital output. • The digital output sampling frequency (fs) does
not match the specifications of the connected
component.
• Set rear panel sampling frequency selector to
match the specifications of the connected
component.
Sound is distorted. • Master output level is too high.
• Input level is too high.
• Adjust master output level ( MASTER LEVEL )
dial or the rear panel master output attenuator
(
MASTER ATT ) switch.
• Adjust the TRIM dial so that the input level
approaches 0 dB on the channel level indicator.
Cross fader doesn’t work. • CROSS FADER ASSIGN switch setting ([ A ],
[ THRU ], [ B ]) is incorrect.
• Correctly set the CROSS FADER ASSIGN switch
for the desired channel.
Can’t perform fader start with
CD player. • The FADER START button is set to OFF.
• Rear panel CONTROL jack is not connected to
CD player.
• Only the rear panel CONTROL jack is connected
to the CD player.
• Set the FADER START button to ON.
• Use a control cable to connect the CONTROL
jacks of mixer and CD player.
• Connect both the CONTROL jacks and analog
input connectors.
Effects don’t work. • Effect channel selecter setting is incorrect.
• Effect parameter 2 adjust dial ( LEVEL/DEPTH ) is
set to [ MIN ].
• Correctly select the channel on which you wish
to apply effects.
• Adjust the effect parameter 2 adjust dial
( LEVEL/DEPTH ).
External effector doesn’t work. • Effect selecter is not set to [ SND/RTN ].
• Effector is not connected to rear panel SEND/
RETURN connector.
• Effect channel selector is set to incorrectly.
• Set effect selector to [ SND/RTN ].
• Connect effector to the rear panel SEND/
RETURN connectors.
• Use the effect channel selector to select the
audio source to which you wish to apply the
effects.
Sound from external effector is
distorted. • Input level from external effector is set too high. • Lower the output level of the external effector.
BPM can’t be measured.
Measured BPM value is
incorrect.
• Input level is too high, or too low.
• BPM may not be correctly measurable with
some tracks.
• Adjust the TRIM dial so that the input level
approaches 0 dB in the channel level indicator.
• Adjust other channels as well so that the input
levels approach 0 dB in the channel level
indicator.
• Strike the TAP button to set BPM manually.
The measured BPM value is
different from the value
published with the CD. • Some differences may occur due to differences
in BPM detection methods.
• No remedy is necessary.
MIDI sequencer can’t be
synchronized. • MIDI sequencer’s synch mode is not set to
“slave”.
• MIDI sequencer is not supported type.
• Set MIDI sequencer’s sync mode to “slave”.
• MIDI sequencers that do not support MIDI
timing clock cannot be synchronized.
01_DJM-700_En.book 25 ページ ２００７年７月１０日 火曜日 午後８時５１分