PYLE Audio PDCD6000MP - Manual (Page 6)

- 5 -
16. ON/OFF BUT TON (PITCH)
Press the button to be PITCH ON mode, press it
again on the PITCH ON mode, and blinks with unit
on the PITCH OFF mode.
17. 3 HOT -CUE
This unit will allow you to play from 3 cue points
instantly.
a. Set CUE memory: Press the MEMO button first,
and then press the CUE button to complete the CUE
setting, then this C UE button will light up.
b. Play” CUE” memory: Upon pressing specific CUE
button, it will flash about 5 seconds.
Note: This function is not available during perform
REV ERSE sound effect.
18. SAM. BUTTON
Sampler is a kind of sound effect that you record the music
from the track. While playing the music, you can use the
sampler to mix with music. The maximum length is 32
seconds.
a. Set start point: Press the MEMO key, and then press SAM
button, after memorizing the SA M button flashes quickly (2
times in 1 sec)
b. Set End point: Press the SAM button again, when the end
point is memorized, the S AM button lights up (not flash).
c. Play Sampler: During PLAY mode, press the SA M button,
then the button will flash slowly. (1 time in 1 sec)
NOTE: Refer to parameter setting instruction for sampler
adjustment
19. JOG WHEEL
*Speed Control (SEARCH indicator off)
Rotating the wheel, in play mode, will change the playback
speed accordingly. While rotating clockwise, the player
speed increase; rotating counterclockwise, the speed
decrease.
*Search (SEARCH indicator lights)
Rotating the wheel, the player will forward or backward
quickly. The searching speed changed according to the
dialing speed. It can be carried out by one frame increment.
20. Seamless Loop (2 set)
There is A, B/LOOP/ EXIT, RELOOP buttons.
1 . A BUTTON---“start point” (A point. Also, Cue 1 could be A
point) After setting up the A point, the red Led light up
2 . B/LOOP/ EXIT BUTTON: ---“ End point”(B point). Press the B
/LOOP button to set up the B point and start the loop playback
automatically. Loop lights on the display and the 3 LEDs flash.
Press this button again to exit the LOOP playback.
3 . Return to the loop playback by pressing the RELOOP while in
performance. However, if your want to return to loop playback,
you can press RELOOP BUTTON
4 . Change “ START POINT” and” END POINT” by pressing the
A& B/ LOOP/ EXIT button again
5 . The interval between A and B point must be more than 20
frames; otherwise, the B point will be canceled, then LOOP
function disappear and LOOP fades on the display
21. SOUND EFFECT/ DIRECT ACCESS
BUTTONS
* SOU ND EFFECT OFF
The buttons are direct access keys (0~9). To select the
number of the track you would like to play.
* SOU ND EFFECT ON
The buttons is for sound effect control and it lights up when
the sound effect be chosen and off when the button is
pressed again.
NOTE: How to set up the parameter; please refer to
parameter setting instruction. (Page7)
SCRATCH: Move the JOG Wheel backward or forward like
scratching a turntable record. This sound effect can be performed
independently, or in parallel with other effect.
BRAKE: To change the speed of PAUSE and START. This sound
effect can be performed independently, or in parallel with other
effect.
REVERSE: The music is playing backward. This sound effect can
be performed independently, or in parallel with other effect.
PHASER: It sounds like the airplane takes off
FLANGER: It sounds like another kind of airplane takes off. .
FILTER: There are bass & treble. To increase the parameter value,
it will cut bass off but keep treble. To decrease the parameter value,
it will cut treble off but keep bass.
CHOP: The music is chopped with break.
PAN: Alternatly playing right and left signal
ECHO:
Have the effect as ECHO.
22. SOUND EFFECT ON/OFF SWIT CH
Press the EFFE CT button to activate or deactivate the
sound effect. While the effect is activated, on the display
the mark
above the effect is light. .
23. EFFECT SELECT KNOB
The parameter of sound effect can be pre-set. Turn the knob until
the LCD shows the effect name that you want, push the button to
select it, and turn this button again to select from the menu for
setting parameter.
24. EFFECT SCOPE KNOB
After the menu of effect is selected, turn this knob to
choose the parameter, the relative value can be shown in
the LCD.
(Please refer to page 7 with the Parameter Setting
Instruction for details)
When the unit is not under parameter adjustment, the
display does not show the effect name, this knob can be
used to adjust the KE Y scale, and press it to lock the key
(the display will show
)
25. RELAY
Press the “RELAY” button to activate. When one unit is in
play mode, and the other unit is in “pause” mode; pause
the playing unit, the other unit will automatically start to play
(the button will blink).
26. BPM BUTTON
You can get the BPM number automatically or manually.
Pressing the BPM BUTTON for 3 seconds to switch
between auto and manual control. The B EAT will be
shown on the display! Under the manual mode, tapping
this button to get the beat value.
27. KEY ON/OFF SWITCH
Press the button to switch KEY mode on or off.
KEY OFF: The display shows the “KEY” in blinking, and the
key changed according to the pitch change. The key
parameter adjustment is not in effect
KEY ON: The “KEY” lights on the display, turning the
SCOPE knob to adjust the key. Slide the pitch slider will also
change the key.
KEY LOCK: Press the SCOPE knob to lock the key as set,
sliding the pitch slider does not change the key.
Please refer to parameter setting instruction. (Page 8)
28. CARD: Switch the playback source to memory card.
29. CONNECTOR PORT
The 8-pin(6-pin) termination permits the connection of the
control unit to the main unit.
30. SLEEP:
Leave the unit unused for 30 minutes; the machine will shut
off automatically.