LG RD-JT41 800X600 SVGA User Manual
Dlp projector, Features
This manual is related to the following products:
Table of contents
Document Outline
- DLP Projector
- Thank you for purchasing the DLP Projector.
- Please read this user’s guide to ensure correct use of the device. Save this user’s guide for fut...
- This DLP Projector can display various computer signals and NTSC/PAL/SECAM video signals.
- Copyright
- Disclaimer
- Introduction
- 1. Read this user’s guide before you operate your projector and save it for future reference.
- 2. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately...
- 3. Never replace the lamp assembly or any electronic components unless the projector is unplugged.
- 4. To reduce the risk of electric shock, do not disassemble this appliance. Take it to a qualifie...
- 5. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaini...
- 6. This product is capable of displaying inverted images for ceiling mount installation. Please u...
- The Projector is shipped with the cables required for connection to standard PC or laptop compute...
- External control panel (see next page)
- Audio/ Video connector
- Projection lens
- Computer Audio IN
- Front adjuster
- USB mouse connector
- IR remote sensor
- S-Video jack
- Ventilation grill
- RS-232C control port
- Speaker
- Rear adjuster feet
- Projection lens adjuster
- Kensington lock
- Computer signal input
- AC power cord inlet
- Computer signal output
- Main power switch
- YPBPR connector
- Lamp door
- The projector is equipped with 2 quick-release adjuster feet. Push the buttons to adjust its tilt...
- The projector integrates high-performance optical engine projection and a user- friendly design t...
- The projector offers the following features:
- Note: The brightness of the projected image will vary depending on the ambient lighting condition...
- The remote control sensors are located in the front/ back of the projector. The distance between ...
- Push and slide the battery compartment lid in the direction shown.
- Installation
- Place the projector at the required distance from the screen according to the desired picture siz...
- L Projection Distance
- HDTV description
- The projector is capable of displaying various High Definition TV display modes. Some of these so...
- Most of these sources will provide an analog component video output, a standard VGA output, or a ...
- The projector is capable of accepting HDTV data through a YPBPR connector. Use a HDTV cable that ...
- The following standards are supported in the HDTV function:
- Please refer to "Menu System" on page 13 for information on the HDTV OSD selections.
- Connecting to Various Equipment
- Operation
- 1. Plug the power cord into a wall socket.
- 2. Turn on the main power switch.
- 3. Press POWER to start the unit. The back-lit POWER key flashes green and stays green when the p...
- (When the power is turned off, there is a 120-second cooling period before the projector can be r...
- Keystoning refers to the situation where the projected image is noticeably wider at either the to...
- In some cases, you may need to optimize the picture quality. To do this, press the AUTO key on th...
- When several input sources are available, press the SOURCE key to make a selection from the contr...
- Press Menu for the main menu, and then press 3or 4 to select a sub-menu. Press Menu again to sele...
- Off
- These functions are available only when the input mode is PC and the PIP source is Video or S-Video.
- Maintenance
- When the Lamp Indicator lights up red or a message appears suggesting the time of lamp replacemen...
- Lamp Life Indicators
- The Lamp is not properly attached
- Lamp temperature is too high
- Please check with LG service center for the information of lamp replacement.
- When the LED lights up, it is warning you of the following possible problems:
- Turn off the projector and contact qualified service personnel for further help.
- Troubleshooting
- Specifications
- Technical Specifications
- Product name
- Personal Projector
- Model name
- RD-JT40 1024X768 XGA
- RD-JT41 800X600 SVGA
- Display system
- 1-CHIP DMD
- Lens F/Number
- F/2.6
- Lamp
- 210W NSH lamp
- Electrical
- Power supply
- AC100 ~ 240V, 3.5A, 50/60 Hz (Automatic)
- Power consumption
- 330 W (Max)
- Dimensions
- 308 mm (W) x 95 mm (H) x 238 mm (D)
- Operating temperature range
- 0˚C ~ 40˚C
- Weight
- 7 lbs (3.2 Kg)
- Computer input
- RGB input
- D-sub 15-pin (female)
- Video signal input
- S-VIDEO
- Mini DIN 4-pin port x1
- VIDEO
- RCA jack x1
- HDTV signal input
- YPBPR RCA jack x3
- Audio signal input
- Audio 1
- Mini jack stero port
- Audio 2
- RCA jack L, R x2
- Output
- USB mouse connector
- A/B series x1
- Speaker
- 3 watt x 1
- Control
- RS-232C
- 9-pin x1
- Resolution
- H Sync (kHz)
- V Sync (Hz)
- Remark
- 640x350
- 31.5
- 70.1
- 640x400
- 37.9
- 85.1
- VESA
- 720x400
- 31.5
- 70.0
- 720x400
- 37.9
- 85.1
- VESA
- 640x480
- 31.5
- 60.0
- VESA
- 640x480
- 37.9
- 72.8
- VESA
- 640x480
- 35.0
- 66.7
- Macintosh
- 640x480
- 43.3
- 85.0
- VESA
- 800x600
- 35.2
- 56.3
- VESA
- 800x600
- 37.9
- 60.3
- VESA
- 800x600
- 48.1
- 72.2
- VESA
- 800x600
- 46.9
- 75.0
- VESA
- 800x600
- 53.7
- 85.1
- VESA
- 832x624
- 49.7
- 74.5
- Macintosh
- 1024x768
- 48.4
- 60.0
- VESA
- 1024x768
- 56.5
- 70.1
- VESA
- 1024x768
- 60.0
- 75.0
- VESA
- 1024x768
- 68.7
- 85.0
- VESA
- 1280x1024
- 64.0
- 60.0
- VESA
- Technical Specifications
- Dimensions
- Unit: mm
- Presses the Power key to turn the projector on or off.
- Automatically determines the best picture settings for current received signals.
- Menu will display the menu system on screen. Press Menu again to access the sub-menus. Left and R...
- Press the Exit button to go back to the main menu. Press Exit again to leave the menu system.
- Selects signal sources from among PC, YPBPR, Video and S- Video.
- The Lamp Indicator will light up when the lamp needs service, cooling or replacement. See “Lamp I...
- The Temp indicator will flash when the system temperature is too high, which may occur if the pro...