Lexmark IBM 9077 User Manual
Lexmark Hardware
Table of contents
Document Outline
- Contents
- Figures
- Tables
- Preface
- Part 1. Introducing and Installing the GRF
- Part 2. Scenarios
- Chapter 3. Installation and Configuration
- 3.1 Initial Configuration
- 3.2 Pre-Installation Assumptions
- 3.3 Installing an SP Switch Router Adapter Card
- 3.4 Attaching SP Switch Router Cables
- 3.5 Configuration Required on the SP System
- 3.6 Multiple Frames for Multiple System Connections
- 3.7 Step-by-Step Media Card Configuration
- 3.8 Step 1. Check SNMP in the SP Switch Router System
- 3.9 Put SNMP Changes into Effect
- 3.10 Step 2. Assign IP Addresses
- 3.11 Step 3. Change Profile Settings
- 3.12 Step 4. Run dev1config
- 3.13 Step 5. Reset SP Switch Router System to Install Files
- 3.14 Verify an SP Switch Router Adapter Card on the Router
- 3.15 Bringing the SP Switch Router Adapter Card Online with the SP
- Chapter 4. Configuration of IP-Forwarding Media Cards
- 4.1 Ethernet 10/100Base-T Configuration
- 4.2 ATM OC-3c Configuration
- 4.2.1 Physical and Logical ATM Interfaces
- 4.2.2 Installing Configurations or Changes
- 4.2.3 Configuration Files and Profiles
- 4.2.4 Assign IP Addresses - grifconfig.conf
- 4.2.5 Specify ATM Card Parameters
- 4.2.6 Configuring PVCs
- 4.2.7 Some maint Commands for the ATM OC-3c Media Card
- 4.2.8 Using grrt to Display the Route Table
- 4.2.9 Using grstat to Display GRF Statistics
- 4.3 ATM OC-12c Configuration
- 4.4 FDDI Configuration
- 4.4.1 Separate Networks versus Bridging
- 4.4.2 Naming the FDDI Interfaces
- 4.4.3 Physical Interface Numbers
- 4.4.4 GRF Interface Name
- 4.4.5 Configuration Files and Profiles
- 4.4.6 Assign IP Addresses - grifconfig.conf
- 4.4.7 Specify FDDI Card Parameters
- 4.4.8 Installing Configurations or Changes
- 4.4.9 Some maint Commands for the FDDI Media Card
- 4.4.10 Using grrt to Display the Route Table
- 4.4.11 Using grstat to Display GRF Statistics
- 4.5 HIPPI Configuration
- 4.6 Configuring Bridging
- 4.6.1 GRF Bridging Implementation
- 4.6.2 Simultaneous Routing and Bridging
- 4.6.3 Configuration Options
- 4.6.4 Interoperability
- 4.6.5 Spanning Tree
- 4.6.6 Bridge Filtering Table
- 4.6.7 Fragmentation
- 4.6.8 Spamming
- 4.6.9 Bridging Components
- 4.6.10 Management Tools
- 4.6.11 Configuration File and Profile Overview
- 4.6.12 Bridging ATM
- 4.6.13 Bridging FDDI
- 4.6.14 Bridging Ethernet
- Chapter 5. Single RS/6000 SP and Single SP Switch Router
- Chapter 6. Multiple RS/6000 SPs and One SP Switch Router
- Chapter 7. Multiple RS/6000 SPs and Multiple GRFs
- Chapter 3. Installation and Configuration
- Appendix A. Laboratory Hardware and Software Configuration
- Appendix B. GRF Configuration Files
- B.1 /root/.profile
- B.2 /etc/Release
- B.3 /etc/bridged.conf
- B.4 /etc/fstab
- B.5 /etc/grarp.conf
- B.6 /etc/gratm.conf
- B.7 /etc/grclean.conf
- B.8 /etc/grclean.logs.conf
- B.9 /etc/grdev1.conf
- B.10 /etc/grifconfig.conf
- B.11 /etc/grlamap.conf
- B.12 /etc/grroute.conf
- B.13 /etc/hosts
- B.14 /etc/inetd.conf
- B.15 /etc/motd
- B.16 /etc/rc.local
- B.17 /etc/snmpd.conf
- B.18 /etc/syslog.conf
- B.19 /etc/ttys
- Appendix C. Hardware and Software Information
- Appendix D. Special Notices
- Appendix E. Related Publications
- How to Get ITSO Redbooks
- List of Abbreviations
- Index
- ITSO Redbook Evaluation