Radio opera, Radio opera radio operation tion tion tion tion, Antennas – Lenoxx Electronics CD-160 User Manual

Page 9: Presetting st

ANTENNAS

The built-in AM Antenna and the FM Telescoping Antenna are directional. You may find

that you can improve AM reception by rotating the set or bringing it closer to a window. The

FM Band can be adjusted by FM Telescoping Antenna. Be sure to extend the FM Telescoping

Antenna carefully to its full length for best reception.

TTTTTO LISTEN T

O LISTEN T

O LISTEN TO PRESET

O PRESET

O PRESET MEMOR

MEMOR

MEMORY

Y ST

STA

ATIONS (after you

TIONS (after you

programmed them)

1. Press the Power Switch ON, the Power/Batt. Lamp will light.

2. Press the Radio Switch, the Radio Indicator will light.

3. Press the Band Switch to select the band you want (AM or FM).

4. Press the Radio Presets Button to select the stations stored (01-10). You will receive

the station you stored into that preset memory. Pressing the button several times will

give you the different preset stations you stored into the preset memories 1 to 10

(Example: Pressing the button 3 times will give you Preset Number 3, press the button

4 times will give you Preset Number 4). Word

PRESET

and Preset Number will show in

the Display.

5. To shut off the radio, press the Power Switch again, the Power/Batt. Lamp will go off.

RADIO OPERA

RADIO OPERATION

TION

TTTTTO PLA

O PLA

O PLAY

Y THE RADIO

THE RADIO

PRESETTING ST

PRESETTING STA

ATIONS

TIONS

UP T

TO 10 AM AND 10 FM ST

O 10 AM AND 10 FM ST

O 10 AM AND 10 FM STA

ATIONS CAN BE ST

TIONS CAN BE ST

TIONS CAN BE STORED INT

ORED INT

ORED INTO THE PRESET

O THE PRESET

MEMORIES. (THEY

MEMORIES. (THEY WILL

WILL

WILL REMAIN IN MEMOR

REMAIN IN MEMOR

REMAIN IN MEMORY

Y AS LONG AS THE BA

AS LONG AS THE BA

AS LONG AS THE BATTERIES

TTERIES

ARE INST

ARE INSTALLED, OR AC POWER CORD IS CONNECTED.)

ALLED, OR AC POWER CORD IS CONNECTED.)

1 . Press the Band Switch to select AM or FM band, and

press the Tuning

Button to select a station.

2. Press the Radio Store (Program) Button,

PROGRAM

will flash in the Display.

PRESET

PROGRAM

Make sure the speakers are connected (speaker wires plugged into the jacks in the back

of the set).

3. While the

PROGRAM

is blinking, press the Radio Presets Button to choose a memory

location (01-10). (Example: Push the Radio Presets Button 3 times for Preset Number 3;

4 times for Preset Number 4.)

4. Press the Radio Store (Program) Button again to confirm. The station now broadcasting

is stored into that preset memory.

NOTE

NOTE: Steps 2-4 should be done quickly.

5. Repeat the above steps 1 to 4 to store other 9 stations into memory.

6. Each memory location (01-10) can store 2 stations, one for AM, the other for FM.

N O T E :

N O T E : Before you disconnect the power (AC and Battery) of the set, make sure the

Power Switch is OFF, then you have approximately 30 seconds to re-connect

the power. Otherwise, the memories may be lost and need to be re-programmed.

1. Press the Power Switch ON (the Power Lamp will light).

2. Press the Radio Switch ON (the Radio Indicator will light).

3. Press the AM/FM Band Switch to select the desired wave band.
4. Tune to desired station by pressing the Tuning

Button. Each time the

button is pressed, the frequency changes.

5. To search for a station quickly (automatic tuning), keep the Tuning

Button

pressed until the station starts to change rapidly, then release the Button and it will stop

at the next strong station.

6. If you tune into a FM stereo station,

will

show in the Display.

7. Adjust the Volume Control to your listening preference.

8. If you prefer more bass, slide the Bass Boost Switch to ON position.

9. To turn off the radio, press the Power Switch again, the Power Lamp will go off.

CD-160S050699 V.2 E