Liebherr HC1001 - Manual (Page 10)

u Connect the IceMaker as indicated the section entitled
Water Supply.*
u Push the appliance 3/4 of the way into the recess.
u Remove the covers (5,6,7) .
u Screw Fig. 11 (61) the equal-
izer trim Fig. 11 (20) to the ap-
pliance through the oblong
holes on top.
Fig. 11
u Fasten all mounting
brackets Fig. 12 (34) with
hex head screws
Fig. 12 (35) to the pre-
bored holes in the appli-
ance door.
Fig. 12
With 5/8 '' (16 mm) thick unit
walls = 22-3/8 '' (568 mm) wide
recess:
u Clip a spacer Fig. 13 (23) onto
the upper hinges and a spacer
Fig. 9 (24) onto the lower hinges.
Fig. 13
u Attach the top and bottom
covers Fig. 14 (53) to the
mounting brackets
Fig. 14 (50) .
u Fasten the mounting
brackets Fig. 14 (50) at the
top with screws Fig. 14 (55)
and at the bottom with
screws Fig. 9 (51) such that
the bracket can still be
moved slightly to the left
and to the right.
Fig. 14
u Remove the protective film from the trim
Fig. 15 (22) .Attach the trim Fig. 15 (22) on
the handle side and flush with the front to
the projecting edge of the cover
Fig. 14 (53) and glue to the sidewall of the
appliance.
u To shorten the trim Fig. 15 (22) at the bot-
tom, if necessary: Position the cover
Fig. 9 (54) on the bottom mounting brack-
et Fig. 14 (50) and shorten the trim
Fig. 15 (22) so that it is flush with the upper
edge of the cover.
Fig. 15
u Remove the cover Fig. 9 (54) again.
To slide the appliance in and align it:
With 5/8 '' (16 mm) thick unit
walls = 22-3/8 '' (568 mm) wide
recess:
u Allow the spacers on the side
wall of the unit to butt up against
the appliance. Fig. 16
With 3/4 '' (19 mm) thick unit
walls = 22-1/8 '' (562 mm) wide
recess:
u Align the front edges of the
hinges flush with the side wall of
the unit.
Fig. 17
For units (5/8 '' (16 mm) and 3/4 '' (19 mm)) with door
stop components (knobs, sealing lips, etc.):
u Allow for the additional distance (depth of door stop com-
ponents). Allow the hinges to protrude by the additional
distance.
u Slide the appliance in until it comes into contact with the
covers Fig. 14 (53) on the side wall of the unit. Fig. 14
u Adjust the adjustable feet Fig. 9 (25) with the supplied
open-ended wrench Fig. 9 (26) to align the appliance ver-
tically.
w The appliance is now correctly positioned in depth. The
gap between the front edge of the side wall of the unit
and the body of the appliance is 1-21/32 '' (42 mm) all the
way around. (Allow for door stop components, such as
knobs and sealing lips.)
Note
Malfunction due to incorrect assembly!
If the spacing is not correct, the door may not close. This
can cause icing up, the formation of condensate, and mal-
functions.
u A continuous space of 1-21/32 '' (42 mm) must be main-
tained. (Allow for door stop components, such as knobs
and sealing lips.)
To secure the appliance in the recess:
u Screw chipboard
screws Fig. 18 (29) on
both doors at the top
and at the bottom
through the hinge
plates.
Fig. 18
On the handle side at the top:
u Slightly loosen the
screws Fig. 19 (55) .
u Secure the top mounting
bracket Fig. 19 (50) to the
unit wall with a ø4x19
chipboard screw
Fig. 19 (29) .
u Break off the protruding
end of the cover
Fig. 19 (53) .
Fig. 19
u Tighten the screws Fig. 19 (55) .
u Place the cover Fig. 19 (53) in position.
On the handle side at the bottom:
Installation
10