Life Fitness CLST - Manual (Page 7)

5
6. Locate both H ANDLEBARS (3). Slide one H ANDLEBAR G ROMMET (27)
over each H ANDLEBAR . The groove of the H ANDLEBAR G ROMMET
should face outward.
7. With the bend of one H ANDLEBAR (3) directed to the outside of the
treadmill, insert the H ANDLEBAR into the R IGHT U PRIGHT H ANDLEBAR
B RACKET (L) as shown. Be sure the handlebar mounting holes are
aligned. Repeat for the left side H ANDLEBAR .
8. Locate the E RGO ™ F RONT C ROSSBAR (4) and position the E RGO
F RONT C ROSSBAR with the plastic C OVER (M) facing upward and
forward as shown. Locate and slide the L EFT and R IGHT I NSIDE
S HROUDS (5 & 6) over the corresponding ends of the E RGO F RONT
C ROSSBAR as shown. Slide the L EFT and R IGHT I NSIDE H ANDLEBAR
S HROUDS towards the center of the E RGO F RONT C ROSSBAR as
shown. Note: Be careful not to damage any wire harnesses that
may be leading from the ends of the E
RGO F RONT C ROSSBAR (4).
9. Install one F RONT C ROSSBAR G ROMMET (26), rounded end first,
over either end of the E RGO F RONT C ROSSBAR (4). Position the
grommets just over the end brackets to meet the overmolding.
Note: Be careful not to damage any wire harnesses that may be
leading from the ends of the E
RGO F RONT C ROSSBAR (4).
10. Position the right end of the E RGO F RONT C ROSSBAR (4) near the
large access hole on the inside of the R IGHT U PRIGHT H ANDLEBAR
B RACKET (L). Align the E RGO F RONT C ROSSBAR M OUNTING H OLES
with those in the R IGHT U PRIGHT H ANDLEBAR B RACKET and secure
using two B OLTS (19), from the inside of the treadmill, and N UTS
(22). Tighten the B OLTS securely. Insert one S CREW (17) from
under the R IGHT U PRIGHT H ANDLEBAR B RACKET . Tighten the S CREW
securely.
11. Position the left end of the E RGO F RONT C ROSSBAR (4) near the
large access hole on the inside of the L EFT U PRIGHT H ANDLEBAR
B RACKET (N). Feed the H EART R ATE C ABLE (O) into the access
hole downward out the bottom of the L EFT U PRIGHT H ANDLEBAR
B RACKET .
Align the crossbar mounting holes with those in the L EFT U PRIGHT
H ANDLEBAR B RACKET and secure using two B OLTS (19), from the
inside of the treadmill, and N UTS (22). Tighten the B OLTS securely.
Insert one S CREW (17) from under the L EFT U PRIGHT H ANDLEBAR
B RACKET . Tighten the S CREW securely.
Note: Be careful not to pinch the H
EART R ATE C ABLE (O) (if
equipped) when assembling the E RGO F RONT C ROSSBAR
(4) to the L EFT U PRIGHT H ANDLEBAR B RACKET .
Feed the H EART R ATE C ABLE (O) upward through the top of the
L EFT U PRIGHT (1).
26
5
26
4
19
L 22
22
17
17
3
6
1
2
M
3
N
O
Note: The CLST model
does not have an
Activity Zone on the
Ergo™ Front Crossbar.