KORG Professional Engineer PA3 - Manual (Page 134)

132 Effects
Modulation and Pitch Shift (Mod./P.Shift)
47: St. Auto Fade Mod.
(Stereo Auto Fade Modulatiom)
This stereo chorus/flanger effect enables you to control the LFO
speed and effect balance using auto fade, and you can spread the
sound by offsetting the phase of the left and right LFOs from
each other.
48: 2Voice Resonator
This effect resonates the input signal at a specified pitch. You can
set the pitch, output level, and pan settings for two resonators
individually. You can control the resonance intensity via an LFO.
a
AUTOFADE Src Off...Tempo
Selects the modulation source that
starts AutoFade
Fade-In Delay
[msec]
00...2000
Sets the fade-in delay time
Rate 1...100
Sets the rate of fade-in
b
LFO Frequency
Mod D-mod,
AUTOFADE
Switches between D-mod and
AUTOFADE for the LFO frequency
modulation
Wet/Dry Mod
D-mod,
AUTOFADE
Switches between D-mod and
AUTOFADE for the effect balance
modulation
c
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
d
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
e
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00 Sets the modulation amount of LFO
speed
f
L Delay Time
[msec]
0.0...500.0 Sets the left channel delay time
R Delay Time
[msec]
0.0...500.0 Sets the right channel delay time
g Depth 0...200 Sets the depth of LFO modulation
h
Feedback –100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the feedback damping amount
in the high range
i
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
AutoFade LFO Frequency
FX Amt
Delay
Delay
Left
Right
Feedback
LFO Shape
LFO Phase
LFO: Tri / Sine
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
a
Control Mode
Manual, LFO,
D-mod Switches the controls of resonance
intensity
LFO/D-mod
Invert
Off, On
Reverses the Voice 1 and 2 control
when LFO/D-mod is selected
b
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
D-mod Src Off...Tempo
Selects the modulation source that
controls resonance intensity
c
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00 MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
d
Mod. Depth –100...+100
Sets the amount of resonance
intensity control via LFO/D-mod
Trim 0...100 Sets the input level at the resonator
e
Voice1: Pitch C0...B8 Sets the voice1 Pitch for resonance
Fine [cents] –50...+50
Fine-adjusts the voice 1 pitch for
resonance
Level 0...100 Sets the Voice1 output level
f
Voice1:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
High Damp [%] 0...100
Sets the damping amount of
resonant sound in the high range
Pan
L6...L1, C,
R1...R6
Sets the Voice1 stereo image
g
Voice2: Pitch C0...B8 Sets the voice 2 Pitch for resonance
Fine [cents] –50...+50
Fine-adjusts the voice 2 pitch for
resonance
Level 0...100 Sets the Voice2 output level
h
Voice2:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
High Damp [%] 0...100
Sets the damping amount of
resonant sound in the high range
Pan
L6...L1, C,
R1...R6
Sets the Voice2 stereo image
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
Resonance
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
High Damp
High Damp
Trim
Trim
+
Level
Level Pan
Pan
Control Mode
D -mod
LFO
Manual
Invert: On/Off
Resonator
Resonator
Pitch, Fine [cents]