KORG Professional Engineer PA3 - Manual (Page 123)

121 Effects
Overdrive, Amp models, and Mic models (OD Amp Mic)
Advanced
25: Bass Amp+Cabinet
(Bass Amp Model+Cabinet)
This simulates a bass amp and speaker cabinet.
a: Amp Type
h: Cabinet Type
Recommended Combinations of Bass Amp Models and Cabi-
nets:
26: Tube PreAmp Model
(Tube PreAmp Modeling)
This effect simulates a two-stage vacuum tube preamp. You can
make individual settings for two vacuum tubes connected in
series. This lets you create the warm sound typical of vacuum
tubes.
a Amp Type
LA STUDIO,
JAZZ ,
GOLD PANEL,
SCOOPED,
VALVE2, VALVE,
CLASSIC
Selects the type of the amplifier
b
Volume 0...100 Sets the output level
Src Off...Tempo
Selects the modulation source for
the output level
Amt –100...+100
Sets the modulation amount of the
output level
c Bass 0...100 Sets the bass (low range) level
d
Middle 0...100 Sets the middle (mid range) level
Mid Range 0...4 Sets the mid-frequency range
e Treble 0...100 Sets the treble (high range) level
f Presence 0...100
Sets the presence (high-frequency
tone)
g
Cabinet
Simulater
Off, On
Switches the cabinet simulator on/
off
h Cabinet Type
LA - 4x10,
MODERN -
4x10,
METAL - 4x10,
CLASSIC -
8x10,
UK - 4x12,
STUDIO - 1x15,
JAZZ - 1x15,
VOX AC100 -
2x15,
US - 2x15,
UK - 4x15,
LA - 1x18,
COMBI - 1x12
& 1x18
Selects the cabinet type
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Amp Type Cabinet Type
LA STUDIO LA - 4x10, LA - 1x18
JAZZ JAZZ - 1x15
GOLD PANEL MODERN - 4x10
SCOOPED METAL - 4x10
VALVE2 CLASSIC - 8x10
VALVE CLASSIC - 8x10
CLASSIC COMBI - 1x12 & 1x18
+
Left
Right
FX Amt
Volume
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
D -mod
Bass Amp Model1 Cabinet Simulator
a
Tube1 Low Cut
[Hz]
Thru, 21...8.00k
Sets the cutoff frequency for the low
cut filter of stage 1
High Cut [Hz]
53...20.00k,
Thru Sets the cutoff frequency for the
high cut filter of stage 1
b
Tube1 Gain
[dB]
–24.0...+24.0 Sets the input gain for stage 1
Saturation [%] 0...100
Sets the input/output response for
stage 1
c Tube1 Bias 0...100 Sets the bias voltage for stage 1
d Tube1 Phase
Normal,
Wet Invert
Turns phase reversal on/off
e
Tube2 Low Cut
[Hz]
Thru, 21...8.00k
Sets the cutoff frequency for the low
cut filter of stage 2
High Cut [Hz]
53...20.00k,
Thru Sets the cutoff frequency for the
high cut filter of stage 2
f
Tube2 Gain
[dB]
–24.0...+24.0 Sets the input gain for stage 2
Saturation [%] 0...100
Sets the input/output response for
stage 2
g Tube2 Bias 0...100
Sets the bias voltage for stage 2
h
Tube2 Output
Level [dB]
–48.0...+0.0 Sets the output level
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
+ Tube Pre Amp1 Tube Pre Amp2
Left
Right
FX Amt
Output Level
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
–
+
Invert