Kenwood KRF-V8030D - Manual (Page 18)

18
Operations
1 Use the INPUP SELECTOR knob to select the source (other than
"MD/TAPE") you want to record.
2 Set the cassette deck or MD recorder to record.
3 Start playback, then start recording.
Recording audio (analog sources)
Recording
Recording a music source
1 Press the MONITOR key.
2 Use the INPUP SELECTOR knob to select a source other than
"MD/TAPE."
3 Start playback on the cassette deck connected to the MONITOR
jacks and start recording on the cassette deck connected to the
MD/TAPE jacks.
Recording tapes or MDs
1 Use the INPUP SELECTOR knob to select "MD/TAPE."
2 Start playback on the cassette deck connected to the MD/TAPE
jacks and start recording on the cassette deck connected to the
MONITOR jacks.
MONITOR = MD/TAPE recording
MD/TAPE = MONITOR recording
• To copy tapes using a double cassette deck, refer to the instruction
manual of the double cassette deck.
MONITOR function (analog sources only)
You can connect a cassette deck or graphic equalizer to the MONITOR
jacks of the receiver. If a graphic equalizer is connected, the MONITOR
key should be left in the on position. Alternately, if a cassette deck
equipped with a 3-head system is connected to the
MONITOR jacks,
you will be able to monitor the just-recorded signal while making
recordings on the cassette deck. By switching the
MONITOR key on
and off, you can compare the sound of the source signal and the just-
recorded signal. For more information, refer to the instruction manual of
the connected component.
INPUT SELECTOR
MONITOR
S.DIRECT
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
STEREO MONITOR
1 Use the INPUT SELECTOR to select the source (CD, DVD,
VIDEO2, or VIDEO3) you want to record.
2 Set the cassette deck or MD recorder to record.
3 Press and hold the DIMMER key for more than 2 seconds to
select the A-REC MODE.
• The mode changes every 2 seconds as shown below.
1 REC MODE off : The digital input record mode is
switched off.
2 A-REC MODE : The digital input signals (DTS,
Dolby Digital, or PCM) are identi-
fied automatically and converted
into stereo signals that are ready
for recording.
3 M-REC MODE : The input signal type at the mo-
ment this mode is selected is held
throughout this mode.
Recording audio (digital sources)
Switch on the REC MODE to record a digital input source.
Usually use the A-REC MODE to record audio input sources.
When the digital mode changes during recording in the A-REC MODE , the
audio may be interrupted momentarily. To record the audio from the
beginning of the digital mode change, use the
M-REC MODE .
4 Start playback, then start recording.
Recording video
1 Use the INPUT SELECTOR to select the video source (other than
“VIDEO1”) you want to record.
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• With certain video software, recording may not be normal due to the
copy guard condition. §
Recording music in A-REC MODE
INPUT SELECTOR
DIMMER
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
DIGITAL AUTO SOUND FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
DIGITAL AUTO SOUND FM
AM
MHz
kHz
3
DOWN MIX
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO
PRO LOGIC
STEREO
STEREO