Kompernass KH 2300 - Manual (Page 12)

DEVICE/ SOURCE SELECT [ » CD / TUNER / TAPE / AUX « ]
• Press the appropriate button
*
to select a device or change the source:
CD = CD player TUNER = radio TAPE = cassette recorder AUX = external device, e.g. record deck
ADJUST VOLUME [ » VOLUME / MUTE « ]
• To increase the volume use the ̆ button
W
.
• To reduce the volume use the ̄ button
Q
.
• To mute (silence) the loudspeakers and headphones press the mute button
^
.
ADJUST TONE [ » CLASSIC / ROCK / POP « ]
Use the tone selector button
%
to set the tone quality of a track to suit the type of music and increase listening pleasure. The
current setting CLASSIC, ROCK or POP is shown in the display
@
- (blank display = neutral tone).
HEADPHONES [ » PHONES « ]
8-32 Ohm stereo headphones
5
can be connected to the headphones connector with a 3.5 mm jack plug. As soon as the headphones
are connected the loudspeakers are turned off. Please note that high levels of sound can lead to serious hearing damage.
SETTING THE TIME
0 1) For you to be able to set the time, the equipment must be in Stand-by mode (operating display
R
lights up red).
0 2) Press MEMORY/CLK-ADJ button
\
once - the hours display flashes.
0 3) Move the hours setting forward or backward using the Forward button
)
or Reverse button
8
.
0 4) Press MEMORY/CLK-ADJ button
\
again - the minutes display flashes.
0 5) Move the minutes setting forward or backward using the Forward button
)
or Reverse button
8
.
0 6) Press the MEMORY/CLK-ADJ button
\
again - the display stops flashing and the clock starts (the colon flashes).
SETTING TIMES FOR SWITCHING ON AND OFF [ » TIMER « ]
If the Switch-on time feature is enabled then your Designer Audio Unit can wake you at your chosen time.
0 1) Using the appropriate button
*
select the desired device/ source (CD, TAPE or TUNER).
0 2) Set up the source, i.e. for TUNER (RADIO) set the desired station, for TAPE (CASSETTE RECORDER) insert the tape and wind
to the correct place or insert a CD and if required program a track sequence.
0 3) Press TIMER button
0
. The display
@
now shows TIMER.
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must begin
again with step 4.
0 4) Press the MODE/REMAIN button
9
twice. The time appears in display
@
and TIMER ON flashes.
0 5) Press the MEMORY/CLK-ADJ button
\
once - the hours display flashes.
0 6) Move the hours setting forward or backward using the Forward button
)
or Reverse button
8
.
0 7) Press MEMORY/CLK-ADJ button
\
again - the minutes display flashes.
0 8) Move the minutes setting forward or backward using the Forward button
)
or Reverse button
8
.
0 9) Press the MEMORY/CLK-ADJ button
\
again - the Switch on time is stored.
10) If you wish to be woken to a cassette: Press the Play button
3
.
11) Then switch off the Designer Audio Unit (ON-/OFF-button
E
).
If you enable the Switch-off time feature, your Designer Audio Unit will always switch off at the set time.
0 1) Press the TIMER button
0
. The display
@
now shows TIMER.
NOTE: You have five seconds to complete the following steps. Otherwise the process is halted and you must
begin again with step 2.
0 2) Press the MODE/REMAIN button
9
three times. The time appears in the display
@
and TIMER OFF flashes.
0 3) Press the MEMORY/CLK-ADJ button
\
once - the hours display flashes.
0 4) Move the hours setting forward or backward using the Forward button
)
or Reverse button
8
.
0 5) Press MEMORY/CLK-ADJ button
\
again - the minutes display flashes.
0 6) Move the minutes setting forward or backward using the Forward button
)
or Reverse button
8
.
0 7) Press the MEMORY/CLK-ADJ button
\
again - the Switch-off time is stored.
To switch off the TIMER functions, press the TIMER button
0
repeatedly until the display
@
shows TIMER.
12