Kenwood B64-2106-00 KRC-16 - Manual (Page 25)

— 25 —
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
General
? The power does not turn ON. 01
✔ The fuse has blown.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
✔ No ACC position on vehicle ignition. 02
☞ Connect the same cable to the ignition as the battery cable.
? If you have selected Standby mode, the power will go OFF
automatically.
03
✔ The Power OFF Timer function has been activated.
☞ If you do not want the power to go OFF automatically, cancel the
Power OFF Timer function.
? Nothing happens when the buttons are pressed. 04
✔ The computer chip in the unit is not functioning normally.
☞ Press the reset button on the unit (page 4).
? There’s a source you can’t switch. 05
✔ There’s no tape inserted.
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't switch to each source.
? There’s a source you can’t switch. 07
✔ The Disc changer isn’t connected. 08
☞ Connect the Disc changer. If the Disc changer isn’t connected to
it's input terminal, You can't switch to an external disc source.
? The faceplate does not open or close. 09
✔ The faceplate is incorrectly attached.
☞ Reattach the faceplate correctly, See the section on
the Faceplate>(page 8).
?
The memory is erased when the ignition is turned OFF. 10
✔ The battery wire has not been connected to the proper terminal.
☞ Connect the wire correctly, referring to the section on
.
✔ The ignition and battery wire are incorrectly connected. 11
☞ Connect the wire correctly, referring to the section on
.
? The TEL mute function does not work. 15
✔ The TEL mute wire is not connected properly.
☞ Connect the wire correctly, referring to the section on
.
? The TEL mute function turns ON even though the TEL mute wire is
not connected.
16
✔ The TEL mute wire is touching a metal part of the car.
☞ Pull the TEL mute wire away from the metal part of the car.
? Even if Loudness is turned ON, high-pitched tone isn't compensated
for.
17
✔ Tuner source is selected.
☞ High-pitched tone isn't compensated for when in Tuner source.
? No sound can be heard, or the volume is low.
✔ The fader or balance settings are set all the way to one side.
21
☞ Center the fader and balance settings.
✔ The input/output wires or wiring harness are connected incorrectly. 22
☞ Reconnect the input/output wires or the wiring harness correctly.
See the section on "Connecting Wires to Terminals".
✔ The cassette tape is bad. 23
☞ Try playing another cassette tape. If works fine, the first tape was
bad.
? The sound quality is poor or distorted. 25
✔ One of the speaker wires is being pinched by a screw in the car.
☞ Check the speaker wiring.
✔ The tape head is dirty. 26
☞ Clean the tape head.
✔ The speakers are not wired correctly. 27
☞ Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
? The Touch Sensor Tone doesn’t sound. 34
✔ The preout jack is being used.
☞ The Touch Sensor Tone can’t be output from the preout jack.
Troubleshooting Guide
KRC-291(E)_U.S_r3 01.10.2 4:47 PM Page 25