State Industries GPO69 700 - Manual (Page 2)

C O M M E R C I A L
E
37˝
B
A
C
D
1 1 ⁄ 2 ˝ NPT INLET &
OUTLET OPENINGS
1˝ NPT T&P VALVE OPENING
27 3 ⁄
4
˝
ELEC.
ENTRY
GPO SUGGESTED SPECIFICATION
ASME
(ON SELECTED MODELS)
e t a m i x o r p p A ) s n o ll a G ( t u p t u O Storage
Input* Shipping
Model Number Capacity
BTU/Hr.
Firing
Recovery
Dimensions In Inches
Wt. (lbs.)
Water
U.S.
Rate
Motor Connections
Gallons
GPH
80°F Rise 100°F Rise 140°F Rise A B C D E
HP
—
—
SPECIFICATIONS
*Based on No.2 fuel oil. Capacity ratings are actual heater performance at 80% thermal efficiency.
**These models are available with ASME construction. When ordering ASME construction, add “ A ” to
end of model model. Example: GPO 69 700OE A
NOTE: Above 2000´ altitude, input ratings should be reduced 4% for each 1000´ above sea level.
Commercial Oil Water Heater
TITAN
™
For more information on Titan ™ contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com
SCOSS00105 January 2013R
Water heater(s) shall be commercial oil model number______________or equivalent. Heater(s) shall have a minimum oil firing rate of ______________gph at 100°F temperature
rise and a storage capacity of _________________gallons. The 160 psi working pressure tank shall be glasslined with the alkaline borosilicate composition being
fused to the steel at 1600° and be equipped with 1-1/3” water inlet and outlet openings, and 2-3/4” x 3-3/4” boiler-type hand-hole cleanout (2) on GPO84 315 and larger
or ASME models. The tank shall be insulated with 2˝ of vermin proof fiber glass insulation. The outer jacket shall have baked enamel finish over a bonderized
undercoating. The burner shall be Underwriters’ Laboratories listed and have a ___________________(one or two) stage oil pump. The burner shall have flame retention,
interrupted ignition and be equipped with primary controls which will provide for 15 second safety shutdown in the event of flame failure. The heater(s) shall be factory
equipped with primary controls which will provide for 15 second safety shutdown in the event of flame failure. The heater(s) shall be factory equipped with temperature
limiting device, drain valve, flame observation port and 180° adjustable thermostat having upper and lower sensing bulbs which average the water temperatures at the
top and bottom of the tank for maximum water temperature control. A pressure and temperature relief valve shall be furnished and installed by the factory. Heater
tank shall have a 3 year limited warranty against corrosion and tank failure due to sediment buildup as outlined in the warranty.
CAUTION: Unit must be installed on non-combustible surface.
MULTIPLE INSTALLATIONS
Furnish and install __________________models as specified with a State (2, 3, or 4) heater manifold kit, package number _____________.
224256 SC0SS00105 2 4/23/10 2:04:33 PM
74-3/4
79-3/4
74-3/4
74-3/4
74-3/4
74-3/4
67-3/4
67-3/4
67-3/4
65
66
70-3/8
25-1/4
25-1/4
30-1/16
27
27
27 6
8
8
8
8
10 29-3/8
23-3/4
23-3/4
23-1/8
23-1/8
23-1/8 1/8
1/8
1/8
1/8
1/8
1/8 1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
1-1/2
739
647
638
557
568
557
853
748
730
668
253806_SC0SS00105.indd 2 253806_SC0SS00105.indd 2 1/29/13 4:12 PM 1/29/13 4:12 PM