State Industries GPO69 700 - Manual

C O M M E R C I A L
Commercial Oil Water Heater
Limited Warranty:
Limited Warranty Outline
–
If the tank should leak any time during the first three
years, under the terms of the warranty, State Water
Heaters will furnish a replacement heater; installation,
labor, handling and local delivery extra.
– NOTE: This Outline Is NOT A Warranty.
complete information, consult the written
warranty or State Water Heaters.
Meets or Exceeds the Thermal Efficiency and/or Standby Loss
Requirements of the U.S. Department of Energy and Current
Edition of ASHRAE/IESNA 90.1
Titan ™ Models Inhibit Lime and Sediment Buildup –
Titan ™ models are warranted against tank failure due to sediment buildup for three years.
Glasslined Tank – Assures years of rust-free clean hot water. 160 psi working pressure.
180° Adjustable Thermostat – Has upper and lower sensing bulbs to average
water temperatures at top and bottom of heater for maximum temperature control (120°-180°).
Safety Shutoff – Limits temperature buildup.
UL Listed Oil Burner – Precision engineered to match the units they are used
with; designed to fire 1.75 to 5.0 gallons of oil per hour. All models equipped with single phase
continuous duty motor 120 volt AC 60 Hz, 3450 rpm with overload switch and interrupted
ignition. Standard burners equipped with single stage pump with 1 or 2 line capability.
Flame retention principle assures high rate of combustion efficiency, yet maintains low
operating noise levels. Fuel unit includes pump, strainer, pressure regulating valve and
ignition transformer. Transformer rated at 120 volt AC, 60 Hz with high voltage secondary,
UL listed for use with No. 1 and 2 commercial grade fuel oil. Burner mounted cadmium
cell relay for flame detection - 15 second safety switch timing eliminates the need for
RA890F Electronic Safeguard. Complies with UL 296-MP 1192.
Efficient Combustion Chamber – Precast, high temperature combustion chamber
made of alumina silica ceramic fiber. Engineered for maximum insulation and heat reflection.
Unique design assures more complete combustion by stabilizing flame pattern.
Interrupted Ignition – Reduces electrical consumption.
Oil Solenoid Safety Valve – Standard on GPO75 385, GPO75 455 and GPO69 700.
3/4” Drain Valve – Provided in lower tank for fast draining.
Two Hand-Hole Cleanouts – Allows easy cleaning on standard models GPO75 385
and larger and ASME models.
Anodic Protection – For longer tank life.
Flame Observation Port – Permits convenient flame check.
Foam Insulation – Saves fuel, helps assure constant temperature, vermin proof.
Jacket – Heavy gauge steel with baked enamel finish over bonderized undercoat. Not
approved for installation on combustible flooring.
Easy To Install Burner – Three bolt mounting of burner assures easy installation.
Barometric Draft Regulator
CSA Certified and ASME Rated T&P Relief Valve
CAUTION: Units must be installed on non-combustible surface.
Other Features:
– Two layers of high temperature ceramic fiber insulation in combustion chamber
– Flame inspection port opening
– Mounted on rugged channel iron skids
– Multiple anodes for protection
Optional Features:
– Two Stage Pump – For use with underground oil storage tanks.
– ASME Construction – Available on models GPO84 315, GPO75 385, GPO75 455,
GPO69 700. ASME units have 160 psi working pressure.
TITAN
™
For more information on Titan ™ contact:
State Water Heaters
500 Tennessee Waltz Parkway, Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com
SCOSS00105 January 2013R
253806_SC0SS00105.indd 1 253806_SC0SS00105.indd 1 1/29/13 4:12 PM 1/29/13 4:12 PM