StarTech.com SV231UADVI - Manual (Page 7)

Keyboard Hotkey Command Reference Chart
Binding/Unbinding control: By default the switch will automatically switch USB hub and audio control to the KVM
port you select to control (bound). If you choose to “unbind” control, you can assign control of the audio and/or
USB hub to a port other than the active computer using the commands above.
Valid hotkey sequences: If you enter the “Define new hotkey sequence” command ([ScrLk]+[ScrLk]+[H]+[ y ] the
value of [ y ] replaces the [ScrLk]+[ScrLk] command with one of the following:
[CapsLk] = [CapsLk]+[CapsLk]
[Esc] = [Esc]+[Esc]
[F12] = [F12]+[F12]
[NumLk] = [NumLk]+[NumLk]
[ScrLk] = [ScrLk]+[ScrLk] (if another key sequence has been enabled)
Programmable Autoscan delay time: [ z ] can be any one of the following values:
1=10 sec., 2=20 sec. through 9=90 sec., 0=100 sec.
Note: Apple computers will need to be programmed using an IBM-compatible keyboard that has a Scroll Lock key.
Instruction Manual
4
Command Name Hotkey Sequence Description
Select active computer [ScrLk]+[ScrLk]+[ x ]
Switches access to the computer connected to the
corresponding port number on the KVM.
([
x ]= a number on the keyboard)
Select USB hub control [ScrLk]+[ScrLk]+[F x ]
Switches which corresponding port number has access to
the to the devices connected to the KVM’s USB hub.
([F
x ] = Function key: F1=Port 1, F2=Port 2, etc.)
Select Audio/Mic output [ScrLk]+[ScrLk]+[F y ]
Switches which port’s speaker and microphone output is
active at the console.
([F
y ] = Function key: F5=Port 1, F6=Port 2, etc.)
Bind computer and USB hub
control (default)
[ScrLk]+[ScrLk]+[Z]
When either the select active computer or select USB hub
control commands are executed, both functions are
switched to the selected port.
Unbind computer and USB
hub control
[ScrLk]+[ScrLk]+[X]
The computer control and USB hub control can be
executed separately; KVM control and USB hub control
control can be assigned to different ports at one time.
Bind computer and Audio/Mic
control (default)
[ScrLk]+[ScrLk]+[Q]
When either the select active computer or select
audio/mic output control commands are executed, both
functions are switched to the selected port.
Unbind computer and
Audio/Mic output control
[ScrLk]+[ScrLk]+[W]
The computer control and USB hub control can be
executed separately; KVM control and Audio/Mic output
control control can be assigned to different ports at one
time.
Select next/previous port [ScrLk]+[ScrLk]+[arrow]
Selects the next (up arrow key) or previous (down arrow
key) numbered port for control.
Select previous port [ScrLk]+[ScrLk]+[BkSp] Selects the most recent previously active port.
Beep sound on/off [ScrLk]+[ScrLk]+[B] Enables/disables audible responses from the KVM.
Define new hotkey sequence [ScrLk]+[ScrLk]+[H]+[ y ]
Change the standard [ScrLk] hotkey to a new value (see
below).
Autoscan [ScrLk]+[ScrLk]+[S]
Automatically switch active ports in sequence every 10
seconds. (Press any key to cancel.)
Autoscan with programmable
delay
[ScrLk]+[ScrLk]+[S]+[ z ]
Autoscan with a delay other than 10 seconds (see below).
Press any key to cancel.