Woodstock SB1039F User Manual
New & changed parts, Manual insert, Ref part # description ref part # description
Manual Insert
PHONE: (360) 734-1540 •
www.southbendlathe.com
MODEL SB1039F
14" X 40" LATHE 220V w/DRO
Copyright © June, 2011 by South Bend Lathe Co.
WARNING: No portion of this manual may be reproduced without written approval.
#BL14239 Printed in USA
The Model SB1039F Lathe is the same machine as the Model SB1039 except for the following:
• Added a 2-Axis Fagor Digital Readout (DRO).
Except for the differences noted in this insert, all other content in the Model SB1039 Owner’s Manual
applies to this machine. Before operating your new lathe, you MUST read and understand this insert,
the entire Model SB1039 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of
injury when using this machine. Keep this insert for later reference.
If you have any further questions about this manual insert or the differences between the Model
SB1039F and the Model SB1039, contact our Technical Support at (360) 734-1639 or email
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1518
PSB1039F1518
DRO ASSEMBLY FAGOR 2-AXIS
1518-3 PSB1039F1518-3 DRO Y-AXIS SCALE FAGOR MKT-22
1518-1 PSB1014F2318-1
DRO DISPLAY FAGOR 20-iT
1601
PSB1039F1601
MACHINE ID LABEL
1518-2 PSB1037F2318-2 DRO X-AXIS SCALE FAGOR MKT-102
1618
PSB1039F1618
MODEL NUMBER LABEL
New & Changed Parts
1618
1518
1518-1
1518-3
1518-2
1601
Motor
: 5/2.5H
P, 22
0V,
3-Ph
, 60
Hz
Full-Lo
ad Cu
rrent R
ating:
14.3
A
Swing Ov
er Bed
: 14
.17"
Distan
ce Between Centers: 40"
Swing Ov
er Cross Slid
e: 8
.66"
Swing Ov
er Gap
: 20
.94
"
Spind
le Nose to
Gap: 6.46
"
Cro
ss Slide T
rav
el: 7
"
Compo
und T
rav
el: 4
"
Spind
le Nose: D
1-5
Camlo
ck
Spind
le Bo
re: 1.5
7"
Taper Inside
Sp
ind
le: MT#5
Taper Inside
Tailstoc
k: MT
#3
Wei
ght:
242
0 lb
s.
Made in T
aiw
an t
o Sou
th Bend
Speci
fica
tions
TO REDUCE THE RISK OF SERI
OUS PERSONAL I
NJUR
Y WHI
LE USING THIS
MA
CHINE:
WA
RN
ING
!
!
MODEL SB1039F
14" x 40" 16 SPEED L
ATHE 22
0V w/D
RO
MFG Date
Serial N
o.
1.
Read and understand manual bef
ore star
ting
.
2.
Always wear appro
ved e
ye protection.
3.
Make sur
e the machine is connected to a grounded po
wer source.
4.
Keep all guards in place.
5.
DO NO
T wear loose clothi
ng, glo
ves
, or je
welr
y; secur
e lo
ng hair and
roll up long slee
ves
.
6.
Disconnect po
wer bef
ore ser
vice, mai
ntenance,
or adjustm
ent
s.
7.
DO NO
T oper
ate when tir
ed or under the influence of
drugs or al
cohol.
8.
Make sur
e the machine is proper
ly adjusted/set up b
efor
e star
ting
.
9.
Change cutting fluid r
egular
ly and av
oid cont
act with
skin.
10.
Make sur
e w
orkpiece i
s proper
ly and secur
ely held in the ch
uck and has
saf
e clear
ance through full rota
tion bef
ore star
ting the l
athe.
11.
Nev
er leav
e the chuck ke
y in the chuck.
12.
Nev
er touch t
he chuck or w
orkpiece when it is i
n motion.
13.
Nev
er leav
e the la
the running una
ttended.
14.
Make sur
e long w
orkpieces ar
e proper
ly suppor
ted.
15.
Always use the proper speed r
ate f
or the ma
terial y
ou
are tur
ning
.
16.
Do not allo
w childr
en to hav
e unsuper
vised access
to the machine.