Sharp AQUOS LC-32D47UN - Manual (Page 21)

21
Position
For adjusting a picture's horizontal and vertical
position.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
For resetting adjustments to the factory preset values, press
a/b to select "Reset", and then press ENTER.
When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
Adjustments are stored separately according to input
source.
When a DTV channel is selected, the horizontal position
cannot be adjusted.
The horizontal and/or vertical position may not be able to
be adjusted or it may be adjusted only to a certain degree.
PC Setup
Input Signal (for Analog PC Input Mode Only)
Some input signals may have to be registered manually
to display properly. The pair of input signals (resolutions)
in the list below is not distinguishable when received.
In such a case, you have to set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
1024 x 768 1360 x 768
You can only select the "Input Signal" on the Setup menu
when receiving one of the 2 input signals listed above.
Auto Sync. (for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts.
No: This function does not work.
When Auto Sync. is successful, "Completed" displays. If
not, Auto Sync. failed.
Auto Sync. may fail even if "Completed" displays.
Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing Auto Sync.
Be sure to connect the PC to the TV and switch it on before
starting Auto Sync.
•
•
•
•
•
•
•
•
•
•
Fine Sync.
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image fl ickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image fl ickers.
For resetting all Fine Sync. adjustment items to the factory
preset values, press
a/b to select "Reset", and then press
ENTER.
It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
PC Audio Select
Determines whether the AUDIO terminal is used for
INPUT 4 (PC-IN) or INPUT 5 (HDMI).
Input 4 (PC): Select this item when the audio signal is
input via the INPUT 4 (PC-IN) terminal using an analog
RGB cable.
Input 5 (HDMI): Select this item when the audio signal is
input via the INPUT 5 (HDMI) terminal using an HDMI-
DVI conversion cable.
When "PC Audio Select" is set to "Input 5 (HDMI)", sound
will not be produced if you use only an HDMI-certifi ed
cable to connect HDMI-compatible equipment. To produce
sound, you should make an analog audio connection.
If you want to connect HDMI-compatible equipment using
only an HDMI-certifi ed cable, set "PC Audio Select" to
"Input 4 (PC)".
HDMI Auto View
To watch an HDMI or PC-IN equipment image,
select "INPUT5", "INPUT6" or "INPUT7" from "INPUT
SOURCE" menu using INPUT on the remote control
unit or on the TV.
Enable: To use View Mode based on signal recognition,
including an HDMI signal.
Disable: No function.
Refer to your external equipment operation manual for the
signal type.
When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
•
•
•
•
•
•
•
On-Screen Display Menu