Shelby CS-500S - Manual (Page 6)

. .
. .
23 6
OPERATION
B. TWO-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION:
Transceiver
Button System Function Remark
F - (C) System’s Trigger Check Press within 3 seconds
F - F - (C) System’s Status Check Press within 3 seconds
F - ( ) Optional Driving Pager Press within 3 seconds
F (1 sec.) LCD screen lamp turns on for 5 seconds. Press and hold for 1 second
F - F - F Clear the Flash Icon and Melody Sound Press within 3 seconds
on the LCD Screen Transmitter
C. LED Status Display Chart:
LED Status LED Status
Off Disarmed 2 flashes... pause Zone 2 / Trigger on Trunk/Hood
Slow flash Armed 3 flashes... pause Zone 3 / Trigger on Door Switch
Fast flash Passive arming 4 flashes... pause Zone 4 / Trigger on Shock Sensor
On (solid) Valet mode 5 flashes... pause Zone 5 / Trigger on Ignition Switch
D. Chirp Indicators E. Parking Light Indicator Display Chart:
1 Chirp Arm 1 Flash Arm
2 Chirps Disarm 2 Flashes Disarm
3 Chirps Ajar Warning 3 Flashes Triggered
6 Chirps Car Locator 12 Flashes Car Locator
F. SYSTEM OPERATING CONDITION:
Siren, Horn Parking Light LED Doors Starter Dome Light
1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable
2. Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash or Off Unlocking Turns on for
30 seconds
3. Trigger Alarming Flashes Slow Flash Disable Flashes
4. Panic Alarming Flashes Flashes
5. Car-Jacking Alarming Flashes Disable Flashes
6. Car Locator 6 Chirps 12 Flashes
1. Timer Setting: Example to 10:30 AM
1. Press & hold the F button for 3 seconds, with two-melody sounds
and the “Hours” digit flashing for adjusting.
2. Press the or button to decrease or increase the “Hour” digit
until 10:00xx
3. Press the F button once again then the “Minute” digit flashes for
adjusting.
4. Press the or button to decrease or increase the “Minutes” digit
until 10:30AM.
5. Press the F button for 2 seconds with one-melody sound to confirm
exiting the timer program mode.
2. Alarm Timer Setting: Example to 6:30 PM
1. Press and hold the button for 3 seconds, with two-melody sound
and the “Hours” digit flashing for adjusting.
2. Press the F button twice, the LCD screen will shows the icon
and the “Hours” digit will flash for adjusting.
3. Press the or button to decrease or increase the “Hour” digit
until 6:xxPM.
4. Press the F button once again then the “Minutes” digit flashes
for adjusting.
5. Press the or button to decrease or increase the “Minutes” digit
until 6:30PM.
6. Press the F button once again then icon flashes for the alarm
“ON or OFF” setting.
7. Press the button to stop the “Alert Alarm Timer”, and the “OFF”
icon will show on the LCD screen.
8. Press F button for 2 seconds with one-melody sound to confirm
exiting the timer program mode.
3. Count Down Timer Setting: Example Set count down
timer at 2:30.
1. Press and hold the F button for 3 seconds, with two-melody
sounds and the “Hours” digit flashing for adjusting.
2. Press the F button 5 times, the LCD screen will shows the
icon and the “Hours” digit is flashes for adjusting.
3. Press the or button to decrease or increase the “Hour” digit
until 2:xx.
LCD REMOTE CONTROL TRANSCEIVER