JVC VM-4200 User Manual
Page 29
27
Setting the High-Definition Signal Types
You can select one of the High-Definition (HD) signal types
through the COMPONENT/RGB B terminals — 1080i or
1035i. Normally set it to “1080i.”
• Without setting “RGB/COMPO.” correctly, you cannot
show any picture though you select the COMPONENT
input (see page 22).
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding
2 to display
the Setup Menu.
2
Press
5/∞ to move the cursor (3) to
“HD SIGNAL MODE.”
• The Setup Menu consists of two pages. If you keep
pressing
5/∞, you can move to the other page from
the current page.
3
Press
2/3 to select the desired setting.
Each time you press the button, the HD signal type
alternates between “1080i” and “1035i.”
• You can select either “1080i” and “1035i” according to
the HD signal you input — whichever gives you
proportionally shaped pictures.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
Setting the Remote-Controllable Input
This function is available only when the optional video input unit
(IF-C42P1G) is installed.
When connecting the external control unit to the REMOTE
MAKE terminal, you need to set the desired input to use,
which you can select from the connected external control unit.
1
On the remote control:
Press MENU/EXIT while holding
VOLUME – to display the Setup Menu.
On the Monitor:
Press MENU while holding
2 to display
the Setup Menu.
2
Press
5/∞ to move the cursor (3) to
“REMOTE SWITCH.”
• The Setup Menu consists of two pages. If you keep
pressing
5/∞, you can move to the other page from
the current page.
3
Press
2/3 to select the desired setting.
Each time you press the button, the Remote Switch
Mode changes as follows:
MODE1
: Input alternates between “VIDEO A” and
“VIDEO B” when controlled from the external
control unit.
MODE2
: Input alternates between “VIDEO A” and
“RGB B/COMPO.” when controlled from the
external control unit.
MODE3
: Input alternates between “VIDEO A” and
“RGB A” when controlled from the external
control unit.
MODE4
: Input alternates between “VIDEO B” and
“RGB B/COMPO.” when controlled from the
external control unit.
MODE5
: Input alternates between “VIDEO B” and
“RGB A” when controlled from the external
control unit.
MODE6
: Input alternates between “RGB B/COMPO.”
and “RGB A” when controlled from the
external control unit.
4
Press MENU/EXIT (or MENU on the
Monitor) once to exit from the menu
operations.
Cursor (
3)
S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
T I M E R
S E T - U P M E N U 1 / 2
A D J U S T :
S E L E C T :
E X I T :
M E N U
: O F F
: O F F
: M O D E 1
: 1 0 8 0 i
Cursor (
3)
S T A T U S D I S P L A Y
C O N T R O L L O C K
R E M O T E S W I T C H
H D S I G N A L M O D E
W H I T E B A L A N C E
T I M E R
S E T - U P M E N U 1 / 2
A D J U S T :
S E L E C T :
E X I T :
M E N U
: O F F
: O F F
: M O D E 1
: 1 0 8 0 i
*
1
*
1
24-33_VM-4200.p65
03.7.23, 9:30 AM
27