Jensen JCR-263 - Manual (Page 7)

6
６． When the preset wake up time is reached the selected wakeup mode turns “On”. The respective
ALARM Indicator
（
ＡＬ１ ｏｒ ＡＬ２）
ａｎｄ
Wakeup mode
ｉｃｏｎ（ ｏｒ ）
will flash.
The alarm will continue to sound and last for
３
0 minutes before turning off automatically.
The alarm remains set and will turn the J
ＣＲ－２６３ on again at the same time on the following day.
７． To stop the alarm before the alarm time elapses, press the ＡＬＡＲＭ ＯＦＦ Button (# 14). The
alarm will stop but the alarm remains set and will turn J
ＣＲ
-
２６３ on again at the same time on the
following day.
８． If you do not want the alarm to turn J
ＣＲ－２６３ on the following day, press the ALARM1
ｏｒ
Ａ ＬＡＲ Ｍ２ Ｂｕｔ ｔｏｎ ｓ ｒ ｅｐｅ ａｔｅ ｄｌｙ ｕｎ ｔｉｌ ｔｈ ｅ Ａ ＬＡＲ Ｍ１
or
ＡＬＡＲＭ２ Indicator(s), Ａ
larm
ｔｉｍｅ（ｓ）ａｎｄ
Wakeup mode Icon
（ ｏｒ ）
disappear in
the LCD.
Note:
If you have chosen “Wake to RADIO” alarm mode, make sure that you have tuned to a station and adjusted the
volume to a comfortable level.
SNOOZE OPERATION
1. When the alarm sounds (buzzer or radio), you can press the SNOOZE Button to extend the alarm time by 9
minutes. The
ｒｅｓｐｅｃｔｉｖｅ
ALARM
Ｉｎｄｉｃａｔｏｒ（ＡＬ１ ｏｒ ＡＬ２） ａｎｄ
Ｗａｋｅｕｐ
mode
Ｉｃｏｎ（ ｏｒ ）
will
ｂｌｉｎｋ ａｎｄ ｔ
he SNOOZE Indicator ‘SNZ’ appears in
the Display. The buzzer or radio will then turn on again when the snooze duration has elapsed.
2. The SNOOZE operation can be repeated several times within the 30 minutes alarm duration.
ＮＡＰ
OPERATION
Ｔｈｅ ＪＣＲ－２６３ ｉｓ ｅｑｕｉｐｐｅｄ ｗｉｔｈ ｔｈｅ ＮＡＰ ｆｕｎｃｔｉｏｎ．
Ｔｈｅ ＮＡＰ ｔｉｍｅ ｉｓ ａｄｊｕｓｔａｂｌｅ ｆｒｏｍ １０ ｔｏ １１９ ｍｉｎｕｔｅｓ．
Ｔｈｅ ｄｅｆａｕｌｔｅｄ ＮＡＰ ｔｉｍｅ ｉｓ ３０ ｍｉｎｕｔｅｓ．
１． Ｔｏ ａｃｔｉｖａｔｅ ｔｈｅ ＮＡＰ ｆｕｎｃｔｉｏｎ， ｉｎ ＰＯＷＥＲ Ｏｆｆ ｍｏｄｅ ｐｒｅｓｓ
ｔｈｅ ＮＡＰ Ｂｕｔｔｏｎ ｏｎｃｅ． Ｔｈｅ Ｄｉｓｐｌａｙ ｗｉｌｌ ｓｈｏｗ ３０ ｍｉｎｕｔｅｓ
ｏｆ ＮＡＰ ｔｉｍｅ
ａｎｄ ＪＣＲ－２６３ ｗｉｌｌ ｔｕｒｎ ｏｎ ｗｈｅｎ ｔｈｅ ３０
ｍｉｎｕｔｅｓ ｈａｓ ｅｌａｐｓｅｄ．
２． Ｔｏ ｉｎｃｒｅａｓｅ ｏｒ ｄｅｃｒｅａｓｅ ｔｈｅ ＮＡＰ ｔｉｍｅ， ｋｅｅｐ
ｐｒｅｓｓｉｎｇ ａｎｄ ｒｅｌｅａｓｅ ｔｈｅ
TIME SET ! or " Buttons until
time (10~119 minutes) is shown in the LCD.