Jensen JCR-263 - Manual (Page 5)

4
TIME SETTING
NOTE:
The clock has to be set when you first plug it in. The following procedure illustrates the setting of the Clock using 7:30
PM as an example time.
1.
Connect the AC cord to an AC 240V~ 50 Hz power outlet. The LCD will show “AM 12 : 00”
Note: Make sure to use an outlet that is always “live”. Do not use an outlet that is controlled by a wall
switch.
2. For best viewing, press the BRIGHTNESS Button (# 14) once to turn on the LCD back-light. Press
the BRIGHTNESS Button (# 14) again the LCD- back light will become brighter. To obtain the
maximum brightness, press the BRIGHTNESS Button (# 14) the third time. Pressing the
BRIGHTNESS Button (# 14) again will turn the back light off.
3. Set the Clock Set Selector (# 18) to the “TIME” position. “AM 12:00” will blink. While “AM 12:00” is
blinking, press and hold the TIME SET
!
or
"
Buttons (# 15 or # 16) to adjust the time. The Hour
and Minute digits will advance forward or backward rapidly.
4. Keep pressing and release the Buttons when the displayed clock time is close to the actual time.
Repeatedly press the
!
or
"
Buttons to adjust the clock time precisely.
Note: Make sure the hour is set so that AM or PM is correctly displayed.
5.
Set the Clock Set Selector (# 18) to the “LOCK” position to complete the time setting. The current
time will be displayed steadily in the LCD.
RADIO OPERATION
１．
Set the Band Switch (# 12) to the AM or FM band as desired. For example FM
ｂａｎｄ ｉｓ
ｓｅｌｅｃｔｅｄ．
２．
Press the RADIO
ＯＮ／ＯＦＦ Ｂｕｔｔｏｎ
(# 4)
ｏｎｃｅ ｔｏ ｔｕｒｎ ｔｈｅ ｒａｄｉｏ
“
ＯＮ
”
． Ｔｈ
e
Ｄｉｓｐｌａｙ ｗｉｌｌ ｓｈｏｗ ｔｈｅ ｆｒｅｑｕｅｎｃｙ
of the FM
ｓｔａｔｉｏｎ ｂｒｉｅｆｌｙ ａｎｄ ｔｈｅｎ ｒｅｔｕｒｎ ｔｏ ｓｈｏｗ ｔｈｅ
ｃｕｒｒｅｎｔ ｔｉｍｅ．
３． Ｔｕｒｎ ｔｏ ｙｏｕｒ ｆａｖｏｒｉｔｅ ｓｔａｔｉｏｎ ｕｓｉｎｇ ｔｈｅ ＴＵＮＩＮＧ
Control (# 13)
．
４． Ａｄｊｕｓｔ ｔｈｅ ｓｏｕｎｄ ｌｅｖｅｌ ｕｓｉｎｇ ｔｈｅ ＶＯＬＵＭＥ
Ｃｏｎｔｒｏｌ
(# 6)
．
５．
Press the RADIO
ＯＮ／ＯＦＦ Ｂｕｔｔｏｎ
(# 4)
ａｇａｉｎ ｔｏ ｔｕｒｎ ｔｈｅ ｒａｄｉｏ
“
ＯＦＦ
”
Note:
I. When listening to an FM program, fully extend the Wire Antenna to insure maximum tuner
sensitivity.